CAT28C16A_04 Datasheet, PDF (3/10 Pages) Catalyst Semiconductor – 16K-Bit CMOS PARALLEL EEPROM

CAT28C16A
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground⁽²⁾ ........... –2.0V to +V_CC + 2.0V
V_CC with Respect to Ground ............... –2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽³⁾ ........................ 100 mA
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation
of the device at these or any other conditions outside of
those listed in the operational sections of this specifica-
tion is not implied. Exposure to any absolute maximum
rating for extended periods may affect device perfor-
mance and reliability.
RELIABILITY CHARACTERISTICS
Symbol
N_END(1, ⁷⁾
T_DR(1, ⁷⁾
V_ZAP(1)
I_LTH(1)(4)
Parameter
Endurance
Data Retention
ESD Susceptibility
Latch-Up
Min
Max
100,000
100
2000
100
Units
Cycles/Byte
Years
Volts
mA
D.C. OPERATING CHARACTERISTICS
VCC = 5V ±10%, unless otherwise specified.
Symbol
ICC
Parameter
VCC Current (Operating, TTL)
ICCC(5)
VCC Current (Operating, CMOS)
ISB
ISBC(6)
VCC Current (Standby, TTL)
VCC Current (Standby, CMOS)
ILI
Input Leakage Current
ILO
Output Leakage Current
VIH(6)
VIL(5)
VOH
VOL
VWI
High Level Input Voltage
Low Level Input Voltage
High Level Output Voltage
Low Level Output Voltage
Write Inhibit Voltage
Limits
Min Typ Max Units
35
mA
25
mA
1
mA
100 µA
–10
10
µA
–10
10
µA
2
VCC +0.3 V
–0.3
0.8
V
2.4
V
0.4
V
3.0
V
Test Conditions
CE = OE = VIL,
f = 1/tRC min, All I/O’s Open
CE = OE = VILC,
f = 1/tRC min, All I/O’s Open
CE = VIH, All I/O’s Open
CE = VIHC,
All I/O’s Open
VIN = GND to VCC
VOUT = GND to VCC,
CE = VIH
IOH = –400µA
IOL = 2.1mA
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC +2.0V for periods of less than 20 ns.
(3) Output shorted for no more than one second. No more than one output shorted at a time.
(4) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to V_CC +1V.
(5) V_ILC = –0.3V to +0.3V.
(6) V_IHC = V_CC –0.3V to V_CC +0.3V.
(7) For the CAT28C16A-20, the minimum endurance is 10,000 cycles and the minimum data retention is 10 years.
Doc. No. 1076, Rev. D
3