LSN2 Datasheet, PDF (2/14 Pages) C&D Technologies – Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters

®
LSN2 Series
Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters
PERFORMANCE SPECIFICATIONS AND ORDERING GUIDE ^➀
Output
Model
VOUT
IOUT
Power
(Volts) (Amps) (Watts)
R/N (mVp-p) ^➁
Typ.
Max.
LSN2-T/6-W3
0.75-3.3
6
19.8
15
25
LSN2-T/6-D12
0.75-5
6
19.8
15
25
LSN2-T/10-W3
0.75-3.3
10
33.0
15
25
LSN2-T/10-D12
0.75-5
10
33.0
30
75
LSN2-T/16-W3
0.75-3.3
16
52.8
25
50
LSN2-T/16-D12 ➅ 0.75-5
16
52.8
30
75
Regulation ➂
Line
Load
±0.3% ±0.3%
±0.3% ±0.3%
±0.3% ±0.3%
±0.3% ±0.3%
±0.3% ±0.3%
±0.3% ±0.3%
Input
VIN Nom.
(Volts)
5
12
5
12
5
12
Range ➄
(Volts)
2.4-5.5
8.3-14
2.4-5.5
8.3-14
2.4-5.5
8.3-14
IIN ➃
(mA/A)
50/4.22
70/2.69
50/6.95
100/4.39
50/11.12
100/7.1
Efficiency
Min. Typ.
92%
94%
90%
93%
93%
95%
93%
95%
93%
95%
92%
94%
Package
(Case/
Pinout)
B12, P69
B12, P69
B11, P68
B11, P68
B11, P68
B11, P68
➀ Typical at TA = +25°C under nominal line voltage and full-load conditions, unless noted. All
models are tested and specified with external 22μF tantalum input and output capacitors.
These capacitors are necessary to accommodate our test equipment and may not be required
to achieve specified performance in your applications. See I/O Filtering and Noise Reduction.
➁ Ripple/Noise (R/N) is tested/specified over a 20MHz bandwidth and may be reduced with
external filtering. See I/O Filtering and Noise Reduction for details.
➂ These devices have no minimum-load requirements and will regulate under no-load
conditions. Regulation specifications describe the output-voltage deviation as the line voltage
or load is varied from its nominal/midpoint value to either extreme.
➃ Nominal line voltage, no-load/full-load conditions.
➄ VIN must be ≥0.5V greater than VOUT.
➅ LSN2-TXX-D12 efficiencies are shown at 5VOUT.
PART NUMBER STRUCTURE
L SN2 - T / 16 - D12 N G - C
Output Configuration:
L = Unipolar
Low Voltage
Non-Isolated SMT
RoHS-6 compliant*
Power Good Output:
Blank = Omitted
G = Installed
Nominal Output Voltage:
0.75-3.3 Volts (W3)
0.75-5 Volts (D12)
On/Off Polarity:
Blank = Positive polarity
N = Negative polarity
*Contact C&D Technologies (DATEL)
for availability.
Maximum Rated Output
Current in Amps
Input Voltage Range:
D12 = 8.3-14 Volts (12V nominal)
W3 = 2.4-5.5 Volts (5V nominal)
Note:
Not all model number combinations are
available. Contact C&D Technologies (DATEL).
www.cd4power.com
LSN2 Series Page 2 of 14