PRN299 Datasheet, PDF (2/3 Pages) California Micro Devices Corp – POSITIVE/POEUDO ECL(PECL)CLOCK TERMINATION NETWORK

CALIFORNIA MICRO DEVICES
PRN299
ABSOLUTE MAXIMUM RATINGS
Parameter
Rating
V_CC1, V_CC2 , V_CC3 & V_CC4 supply voltage
Diode D1 forward current
GND-0.5, +6.0
100
DC voltage at inputs:
VIDEO_1, VIDEO_2, VIDEO_3
TERM_1, TERM_2, TERM_3
GND-0.5, V_CC1+0.5
-6.0, +6.0
DDC_IN1, DDC_IN2
DDC_OUT1, DDC_OUT2
SYNC_IN1, SYNC_IN2
Temperature:
GND-0.5, V_CC2+0.5
GND-0.5, V_CC3+0.5
GND-0.5, V_CC4+0.5
Storage
-40 to +150
Operating Ambient
0 to +70
Package power dissipation
1.0
Unit
V
uA
V
V
V
V
V
o_C
o_C
W
ELECTRICAL OPERATING CHARACTERISTICS
(over operating conditions unless specified otherwise)
Symbol Parameter
Conditions
MIN
TYP
MAX UNIT
I_CC1
I_{CC2, 3}
I_CC4
V_CC1 supply current
V_CC2, V_CC3 supply current
V_CC4 supply current
V_CC1 = 5V; VIDEO inputs at V_CC1 or GND
V_CC2 = V_CC3 = 5V
V_CC4 = 5V; SYNC inputs at GND or V_CC4;
PWR_UP pin at V_CC4; SYNC outputs unloaded
V_CC4 = 5V; SYNC inputs at 3.0V; PWR_UP
pin at V_CC4; SYNC outputs unloaded
V_CC4 = 5V; PWR_UP input at GND; SYNC
outputs unloaded
10
uA
10
uA
10
uA
200
uA
10
uA
V_BIAS
R_T
V _IH
V _IL
V _OH
V_OL
R_b, R_p
R_c
I_N
I_OFF
V_ON
V_BIAS open circuit voltage
VIDEO termination resistance
R_T resistance matching
Logic High input voltage¹
Logic Low input voltage¹
Logic High output voltage¹
Logic Low output voltage¹
Resistor value
V_{CC 2} pull-down resistor
Input current
VIDEO inputs
HSYNC, VSYNC inputs
OFF state leakage current, level
shifting NFET
Voltage drop across level
shifting NFET when turned ON
No external current drawn from V_BIAS pin
V_CC4 = 5.0V
V_CC4 = 5.0V
I_OH = -4mA, V_CC4 = 5.0V
I_OL = 4mA, V_CC4 = 5.0V
PWR_UP, V_CC3 = 5.0V
V_CC2 = 3.0V
V_CC1 = 5V; V_IN = V_CC1 or GND
V_CC4 = 5V; V_IN = V_CC4 or GND
(V_CC2 - V_{DDC_IN}) < 0.4V; V_DDC__OUT= V_CC2
(V_CC2 - V_{DDC_OUT}) < 0.4V; V_DDC__IN= V_CC2
V_CC2 = 2.5V; V_S = GND, I_DS = 3mA
V_CC4-0.8
V
71.25
75
78.75 Ω
1
2
%
2.0
V
0.8
V
4.4
V
0.4
V
0.5
1
2
MΩ
0.5
1.5
3
MΩ
±1
µA
±1
µA
10
µA
10
µA
0.15
V
C_IN
Input capacitance ³
VIDEO_1, VIDEO_2, VIDEO_3
V_CC1 = 5.0V; V_IN = 2.5V; measured at 1MHz
4.0
pF
V_CC1 = 2.5V; V_IN = 1.25V; measured at 1MHz
4.5
t_PLH
SYNC drivers L-H propagation delay C_L = 50 pF; V_CC = 5V; Input t_r and t_f < 5ns
8
12
ns
t_PHL
SYNC drivers H-L propagation delay C_L = 50 pF; V_CC = 5V; Input t_r and t_f < 5ns
8
12
ns
t_r, t_f
SYNC drivers output rise & fall times C_L = 50 pF; V_CC = 5V; Input t_r and t_f < 5ns
7
ns
V_ESD
ESD withstand voltage^{2, 3}
V_CC1 = V_CC3 = V_CC4 = 5V
±8
kV
Note 1: These parameter applies only to the HSYNC and VSYNC channels.
Note 2:
Per the IEC-61000-4-2 International ESD Standard, Level 4 contact discharge method. V_CC1, V_CC3 and V_CC4 must be bypassed
to GND via a low impedance ground plane with a 0.2uF, low inductance, chip ceramic capacitor at each supply pin. ESD pulse
is applied between the applicable pins and GND. ESD pulse can be positive or negative with respect to GND. Applicable pins
are: VIDEO_1, VIDEO_2, VIDEO_3, SYNC_OUT1, SD1, SYNC_OUT2, SD2, DDC_OUT1 and DDC_OUT2. All other pins are ESD
protected to the industry standard 2kV per the Human Body model (MIL-STD-883, Method 3015).
Note 3: This parameter is guaranteed by design and characterization.
©2000 California Micro Devices Corp. All rights reserved.
2
215 Topaz Street, Milpitas, California 95035 Tel: [phone] Fax: [phone] www.calmicro.com
3/00