PCM1742 Datasheet, PDF (3/22 Pages) Burr-Brown (TI) – 24-Bit, 192kHz Sampling Enhanced Multilevel, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER

SPECIFICATIONS (Cont.)
All specifications at T_A = +25°C, V_CC = 5.0V, V_DD = 3.3V, system clock = 384f_S (f_S = 44.1kHz), and 24-bit data, unless otherwise noted.
PCM1742E
PCM1742KE
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL FILTER PERFORMANCE (Cont.)
Filter Characteristics 2, Slow Roll-Off
Passband
Passband
Stopband
Passband Ripple
Stopband Attenuation
Delay Time
De-Emphasis Error
±0.5dB
–3dB
Stopband = 0.884f_S
0.884f_S
–40
0.198f_S
0.390f_S
±0.5
dB
dB
20/f_S
sec
±0.1
dB
ANALOG FILTER PERFORMANCE
Frequency Response
POWER SUPPLY REQUIREMENTS⁽⁴⁾
Voltage Range, V_DD
V_CC
Supply Current, I_DD
I_CC
Power Dissipation
TEMPERATURE RANGE
Operation Temperature
Thermal Resistance
θ_JA
f = 20kHz
f = 44kHz
f_S = 44.1kHz
f_S = 96kHz
f_S = 192kHz
f_S = 44.1kHz
f_S = 96kHz
f_S = 192kHz
f_S = 44.1kHz
f_S = 96kHz
f_S = 192kHz
SSOP-16
–0.03
dB
–0.20
dB
+3.0
+3.3
+3.6
VDC
+4.5
+5.0
+5.5
VDC
6.0
10
mA
13
mA
16
mA
8.5
13
mA
9.0
mA
9.0
mA
62
98
mW
88
mW
98
mW
–25
+85
°C
115
°C/W
NOTES: (1) Pins 1, 2, 3, 16 (SCK, BCK, LRCK, DATA). (2) Pins 13-15 (MD, MC, ML). (3) Pins 11, 12 (ZEROR, ZEROL). (4) Analog performance specifications are
tested with a Shibasoku #725 THD Meter with 400Hz HPF on, 30kHz LPF on, and an average mode with 20kHz bandwidth limiting. The load connected to the analog
output is 5kΩ or larger, via capacitive coupling. (5) Conditions in 192kHz operation are: system clock = 128f_S and oversampling rate = 64f_S of Register 18.
ABSOLUTE MAXIMUM RATINGS
Power Supply Voltage, V_DD .............................................................. +4.0V
V_CC .............................................................. +6.5V
Ground Voltage Differences .............................................................. ±0.1V
Digital Input Voltage ................................................ –0.3V to (6.5V + 0.3V)
Input Current (except power supply) ............................................... ±10mA
Ambient Temperature Under Bias .................................. –40°C to +125°C
Storage Temperature ...................................................... –55°C to +150°C
Junction Temperature .................................................................... +150°C
Lead Temperature (soldering, 5s) ................................................. +260°C
Package Temperature (IR reflow, 10s) .......................................... +235°C
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER⁽¹⁾
TRANSPORT
MEDIA
PCM1742E
"
PCM1742KE
"
SSOP-16
"
SSOP-16
"
322
–25°C to +85°C
PCM1742E
PCM1742E
Rails
"
"
"
PCM1742E/2K
Tape and Reel
322
–25°C to +85°C
PCM1742KE
PCM1742KE
Rails
"
"
"
PCM1742KE/2K
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces
of “PCM1742E/2K” will yield a single 2000-piece Tape and Reel.
PCM1742
3
SBAS176