OPA357 Datasheet, PDF (2/23 Pages) Burr-Brown (TI) – 250MHz, Rail-to-Rail I/O, CMOS Operational Amplifier with Shutdown

OPA357
OPA2357
SBOS235C − MARCH 2002− REVISED MAY 2004
ABSOLUTE MAXIMUM RATINGS⁽¹⁾
Supply Voltage, V+ to V− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5V
Signal Input Terminals Voltage(2) . . . (V−) − (0.5V) to (V+) + (0.5V)
Current(2) . . . . . . . . . . . . . . . . . . . . . 10mA
Enable Input . . . . . . . . . . . . . . . . . . . . (V−) − (0.5V) to (V+) + (0.5V)
Output Short-Circuit(3) . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . −55°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
(1) _{Stresses above these ratings may cause permanent damage.}
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not supported.
(2) _{Input terminals are diode-clamped to the power-supply rails.}
Input signals that can swing more than 0.5V beyond the supply
rails should be current limited to 10mA or less.
(3) _{Short-circuit to ground, one amplifier per package.}
www.ti.com
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instruments
recommends that all integrated circuits be handled with appropriate
precautions. Failure to observe proper handling and installation
procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION⁽¹⁾
PRODUCT
PACKAGE−LEAD
PACKAGE
DESIGNATOR(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
OPA357
″
SO-8 PowerPAD
″
DDA
″
−40°C to +125°C
″
OPA357A OPA357AIDDA
Rails, 97
″
OPA357AIDDAR Tape and Reel, 2500
OPA357
″
SOT23-6
″
DBV
″
−40°C to +125°C
″
OADI
″
OPA357AIDBVT Tape and Reel, 250
OPA357AIDBVR Tape and Reel, 3000
OPA2357
″
MSOP-10
″
DGS
″
−40°C to +125°C
″
BBG
″
OPA2357AIDGST Tape and Reel, 250
OPA2357AIDGSR Tape and Reel, 2500
(1) _{For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet.}
PIN CONFIGURATION
Top View
OPA357
Out 1
V− 2
+In 3
6 V+
5 Enable
4 −In
SOT23⁽¹⁾
OPA357
NC⁽²⁾ 1
−In 2
+In 3
V− 4
8 Enable
7 V+
6 Out
5 NC⁽²⁾
SO PowerPAD⁽³⁾
Out A 1
−In A 2
+In A 3
V− 4
Enable A 5
OPA2357
A
B
MSOP−10
10 V+
9 Out B
8 −In B
7 +In B
6 Enable B
NOTES: (1) Pin 1 of the SOT23-6 is determined by orienting the package marking as indicated in the diagram.
(2) NC means no internal connection.
(3) PowerPAD should be connected to V− or left floating.
2