OPA353 Datasheet, PDF (10/11 Pages) Burr-Brown (TI) – High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifier ™ Series

Figure 5 shows the OPA353 driving an ADS7861. The
ADS7861 is a dual, 12-bit, 500kHz sampling converter in
the small SSOP-24 package. When used with the miniature
package options of the OPA353 series, the combination is
ideal for space-limited and low power applications. For
further information consult the ADS7861 data sheet.
OUTPUT IMPEDANCE
The low frequency open-loop output impedance of the
OPA353’s common-source output stage is approximately
1kΩ. When the op amp is connected with feedback, this
value is reduced significantly by the loop gain of the op
amp. For example, with 122dB of open-loop gain, the
output impedance is reduced in unity-gain to less than
0.001Ω. For each decade rise in the closed-loop gain, the
loop gain is reduced by the same amount which results in
a ten-fold increase in output impedance (see the typical
performance curve, “Output Impedance vs Frequency”).
At higher frequencies, the output impedance will rise as
the open-loop gain of the op amp drops. However, at these
frequencies the output also becomes capacitive due to
parasitic capacitance. This prevents the output impedance
from becoming too high, which can cause stability prob-
lems when driving capacitive loads. As mentioned previ-
ously, the OPA353 has excellent capacitive load drive
capability for an op amp with its bandwidth.
VIDEO LINE DRIVER
Figure 6 shows a circuit for a single supply, G = 2 com-
posite video line driver. The synchronized outputs of a
composite video line driver extend below ground. As
shown, the input to the op amp should be ac-coupled and
shifted positively to provide adequate signal swing to
account for these negative signals in a single-supply con-
figuration.
The input is terminated with a 75Ω resistor and ac-coupled
with a 47µF capacitor to a voltage divider that provides the
dc bias point to the input. In Figure 6, this point is
approximately (V–) + 1.7V. Setting the optimal bias point
requires some understanding of the nature of composite
video signals. For best performance, one should be careful
to avoid the distortion caused by the transition region of
the OPA353’s complementary input stage. Refer to the
discussion of rail-to-rail input.
C_B1
2kΩ
2kΩ
V_IN B1
2kΩ
2
4
1/4
3 ^OPA4353
C_B0
2kΩ
V_IN B0
2kΩ
6
1/4
7
5 ^OPA4353
C_A1
2kΩ
V_IN A1
2kΩ
9
1/4
8
10 ^OPA4353
C_A0
2kΩ
+5V
0.1µF
0.1µF
24
13
2
CH B1+
3
CH B1–
4
CH B0+
5
CH B0–
6
CH A1+
7
CH A1–
8
CH A0+
9
CH A0–
10
REF_IN
11
REF_OUT
+V_D
+V_A
23
Serial Data A
22
Serial Data B
21
BUSY
20
CLOCK
ADS7861
19
CS
18
RD
17
CONVST
16
A0
15
M0
14
M1
DGND
AGND
1
12
Serial
Interface
V_IN A0
1/4
14
OPA4353
11
V_IN = 0V to 2.45V for 0V to 4.9V output.
Choose C_B1, C_B0, C_A1, C_A0 to filter high frequency noise.
FIGURE 5. OPA4353 Driving Sampling A/D Converter.
®
OPA353, 2353, 4353
10