CHPREZTR Datasheet, PDF (2/5 Pages) Bourns Electronic Solutions – CR0603/CR0805/CR1206 - Chip Resistors

CR0603/CR0805/CR1206 - Chip Resistors
Performance Characteristics (Tests According to MIL-STD-202, MIL-R-55342B, EIA RS-396)
Test
Procedure
Method
Specification
DC Resistance
Thermal Shock
Low Temperature
Operation
Short Time
Overload
High Temperature
Exposure
Resistance to
Soldering Heat
Moisture
Resistance
Load Life
1000 Hours
Solderability
Terminal Strength
Current Noise
—
-40 °C, 60 minutes;
+125 °C, 60 minutes
-55 °C, 1 hour off;
45 minutes on
Rated Voltage x 2.5;
5 seconds
CR0603: 100 V max.
CR0805; 300 V max.
CR1206: 400 V max.
+125 °C; 1000 hours
260 °C, 10 seconds
MIL-STD-202 303
EIA RS-396 4.4
MIL-STD-202 107
EIA RS-396 4.5
MIL-R-55342D 4.7.4
EIA RS-396 4.6
MIL-R-55342D 4.7.5
EIA RS-396 4.7
MIL-R-55342D 4.7.2
MIL-R-55342D 4.7.3
MIL-R-55342D 4.7.4
MIL-R-55342D 4.7.5
MIL-R-55342D 4.7.6
EIA RS-396 4.8
MIL-R-55342D 4.7.7
MIL-R-55342D 4.7.6
MIL-R-55342D 4.7.7
90-98 %RH; 10 cycles MIL-STD-202 106D
EIA RS-396 4.9
MIL-R-55342D 4.7.8
+70 °C; 1.5 hours on,
0.5 hours off;
1000 hours
MIL-STD-202 108
Condition D
EIA RS-396 4.12
MIL-R-55342D 4.7.10
+235 °C; 3 seconds
MIL-STD-202 208
EIA RS-396 4.11
MIL-R-55342D 4.7.11
Pull Test
MIL-R-55342D 4.7.12 MIL-R-55342D 4.7.12
Quan-Tech Model 315B MIL-STD-202 308
MIL-R-55342D 6.6
Humidity,
Steady State
+40 °C; 90-95 % RH, MIL-STD-202 103B —
1344 Hours
Condition D
Salt Spray
96 hours
MIL-STD-202 101D —
Condition A
Vibration
10-2000 Hz, 6 hours MIL-STD-202 201A —
Voltage Coefficient —
MIL-STD-202 309
—
Insulation
Resistance
Test Potential 500V
MIL-STD-202 302
—
CR0603: 100V
Condition B
Dielectric
—
Withstanding
Voltage
MIL-STD-202 301
—
Drop Test
1m
MIL-STD-202 203B —
Bending Test
5 mm/90 mm; 10 sec. —
—
Deviation from Nominal
1%
F:≤±1 %
5%
≤±5.0 %
≤±0.5 % +0.05 Ω
≤±1 % +0.05 Ω
≤±0.5 % 0.05 Ω
≤±1.0 % +0.05 Ω
≤±1 % +0.05 Ω
≤±2.0 % +0.05 Ω
≤±1.0 % +0.05 Ω
≤±0.5 % +0.05 Ω
≤±0.5 % +0.05 Ω
≤±1.0 % +0.05 Ω
≤+2.0 % +0.1 Ω
≤±1.0 % +0.05 Ω
≤±2.0 % +0.05 Ω
≤±3.0 % +0.1 Ω
≥95 % of area
covered
≥500 g
R≤1k Ω; max. 1 µV/V
R≤10k Ω; max. 3 µV/V
R≤100k Ω; max. 6 µV/V
R≤1M Ω; max. 10 µV/V
≤±2.5 % +0.05 Ω
≥95 % of area
covered
≥500 g
R≤1k Ω; max. 1 µV/V
R≤10k Ω; max. 3 µV/V
R≤100k Ω; max. 6 µV/V
R≤2M Ω; max. 10 µV/V
≤±2.5 % +0.05 Ω
≤±1.0 % +0.2 Ω
≤±1.0 % +0.1 Ω
≤±0.5 % +0.1 Ω
≤100 ppm/V
≥10³M Ω
≤±1.0 % +0.1 Ω
≤100 ppm/V
≥10³M Ω
≥500 V (CR1206, CR0805)
≥300 V (CR0603)
≤±0.5 % +0.1 Ω
≤±1 % +0.05 Ω
≤±1.0 % +0.1 Ω
≤±1.0 % +0.05 Ω
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.