TBU-CX025-VTC-WH_11 Datasheet, PDF (1/5 Pages) Bourns Electronic Solutions – TBU® High-Speed Protectors

*RoHS ^COMPLIANT
0C07X585
Features
■ Superior circuit protection
■ Overcurrent and overvoltage protection
■ Blocks surges up to rated limits
■ High-speed performance
■ Small SMT package
■ RoHS compliant*
■ Agency recognition:
Applications
■ Voice / VDSL cards
■ Protection modules and dongles
■ Process control equipment
■ Test and measurement equipment
■ General electronics
TBU-CX Series - TBU^® High-Speed Protectors
General Information
The TBU-CX Series of Bourns^® TBU^®
products are low capacitance dual bidirec-
tional high-speed protection components,
constructed using MOSFET semiconductor
technology, and designed to protect against
faults caused by short circuits, AC power cross,
induction and lightning surges.
External Resistor
Line In/
R
Line Out/
Line Out
Line In
The TBU^® high-speed protector placed in the system circuit will monitor the current
with the MOSFET detection circuit triggering to provide an effective barrier behind
which sensitive electronics will not be exposed to large voltages or currents during
surge events. The TBU^® device is provided in a surface mount DFN package and
meets industry standard requirements such as RoHS and Pb Free solder reflow profiles.
Agency Approval
Description
UL
File Number: E315805
Absolute Maximum Ratings (@ T_A = 25 °C Unless Otherwise Noted)
Symbol Parameter
Part Number
Value
Unit
TBU-CX025-VTC-WH
250
TBU-CX040-VTC-WH
400
V_imp
Peak impulse voltage withstand with duration less than 10 ms TBU-CX050-VTC-WH
500
V
TBU-CX065-VTC-WH
650
TBU-CX085-VTC-WH
850
V_rms
Continuous A.C. RMS voltage
TBU-CX025-VTC-WH
100
TBU-CX040-VTC-WH
200
TBU-CX050-VTC-WH
250
V
TBU-CX065-VTC-WH
300
TBU-CX085-VTC-WH
425
T_op
T_stg
T_jmax
ESD
Operating temperature range
Storage temperature range
Maximum Junction Temperature
HBM ESD Protection per IEC 61000-4-2
-40 to +125
°C
-65 to +150
°C
+125
°C
±2
kV
Electrical Characteristics (@ T_A = 25 °C Unless Otherwise Noted)
Symbol
I_trigger
R_device
t_block
I_Q
V_reset
R_th(j-l)
R_th(j-l)
Parameter
Part Number
Current required for the device to go from operating state to
protected state (R_external = 0 ohm)
TBU-CXxxx-VTC-WH
Series resistance of
the TBU device
(R_external = 0 ohm)
V_imp = 250 V I_trigger (min.) = 500 mA
V_imp = 400 V I_trigger (min.) = 500 mA
V_imp = 500 V I_trigger (min.) = 500 mA
V_imp = 650 V I_trigger (min.) = 500 mA
V_imp = 850 V I_trigger (min.) = 500 mA
TBU-CX025-VTC-WH
TBU-CX040-VTC-WH
TBU-CX050-VTC-WH
TBU-CX065-VTC-WH
TBU-CX085-VTC-WH
Time for the device to go from normal operating state to protected state
Current through the triggered TBU® device with 50 Vdc circuit voltage
Voltage below which the triggered TBU® device will transition to normal operating
state
Junction to package pads - FR4 using recommended pad layout
Junction to package pads - FR4 using heat sink on board (6 cm²) (1 in²)
Min.
500
0.25
12
Typ.
750
2.6
3.6
5.0
7.0
10.7
0.50
16
98
40
Max.
1000
3.0
4.2
5.7
8.0
13.0
1
1.00
20
Unit
mA
Ω
µs
mA
V
°C/W
°C/W
*RoHS Directive 2002/95/EC Jan 27, 2003 including Annex.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.