PDB185-GTR Datasheet, PDF (1/4 Pages) Bourns Electronic Solutions – 17 mm Guitar Potentiometer w/Latching-Push Switch

*RoHS ^COMPLIANT
Features
■ Split knurled or plain shaft options
■ DPDT latching-push switch
■ Metal bushing and shaft
■ Carbon element
■ Linear and audio taper options
■ RoHS compliant*
PDB185-GTR - 17 mm Guitar Potentiometer w/Latching-Push Switch
Electrical Characteristics
Taper.................................. Linear, audio
Standard Resistance Range
........................10K ohms to 1M ohms
Standard Resistance Tolerance....±20 %
Residual Resistance................ 2 Ω max.
Environmental Characteristics
Operating Temperature
..................................-10 °C to +70 °C
Power Rating
Linear ..................................... 0.1 watt
Audio .................................... 0.05 watt
Maximum Operating Voltage
Linear .........................................150 V
Audio ..........................................100 V
Sliding Noise........................47 mV max.
Mechanical Characteristics
Mechanical Angle ................... 300 ° ±5 °
Rotational Torque ...........20 to 150 g-cm
Stop Strength..................... 8 kg-cm min.
Rotational Life...................15,000 cycles
Switch Life ................. 10,000 actuations
Switch Type .................................. DPDT
Switch Travel ..................... 4.0 ± 0.8 mm
Switch Operating Force ..........2 kgf max.
Switch Operating Speed................1 sec.
Soldering Condition
Wave ...........260 °C max., 5 sec. max.
Manual ........350 °C max., 3 sec. max.
Hardware .............. Two flat washers and
two mounting nuts supplied per
potentiometer
How To Order
PDB185 - GTR 11 - 504 A2
Model
Guitar Pot Designator
Configuration
• 01 = Knurled Shaft (18 Tooth) /
Solder Lugs
• 02 = Slotted Shaft / Solder Lugs
• 04 = Slotted Shaft/PC Pins
• 11 = Knurled Shaft (24 Tooth) /
Solder Lugs
• 13 = Knurled Shaft (24 Tooth) /
PC Pins
• 31 = Knurled Shaft (18 Tooth) /
Solder Lugs, Long Bushing
• 32 = Slotted Shaft / Solder Lugs /
Long Bushing
• 33 = Knurled Shaft (24 Tooth) /
Solder Lugs, Long Bushing
Resistance Code (See table)
Resistance Taper (See taper charts)
Product Dimensions
PDB185-GTR01
9.5 ± 0.3
(.374 ± .012)
19.0 ± 0.5
(.748 ± .020)
7.0 ± 0.3
(.276 ± .012)
6.0 ± 0.3
(.236 ± .012)
3/8 ”-32
C
0.5
(.020
±
±
0.3
.012)
UNEF-2A THREAD
4.0 +0.8/-0.5
(.157 +.031/-.020)
SWITCH TRAVEL
1.0 ± 0.3
(.039 ± .012)
(18 TEETH)
6.0 ± 0.3
(.236 ± .012)
DIA.
DIMENSIONS:
MM
(INCHES)
PDB185-GTR02
2.0 ± 0.3
(.079 ± .012)
6.0 ± 0.3
(.236 ± .012)
27.3 ± 0.5
(1.075 ± .020)
9.5 ± 0.5
(.374 ± .020)
19.0 ± 0.5
(.748 ± .020)
1.0 ± 0.3
(.039 ± .012)
4.0 +0.0/-0.8
(.157 +.000/-.031)
SWITCH TRAVEL
1.0 ± 0.3
(.039 ± .012)
16.8 ± 0.5
(.661 ± .020)
1.0 ± 0.3
(.039 ± .012)
MAX.
4.0 ± 0.3
(.157 ± .012)
SHAFT SHOWN IN
FULL CCW POSITION
60 °
3/8 ”-32
C
0.5
(.020
±
±
0.3
.012)
UNEF-2A THREAD
6.35 +0.0/-0.1
(.350 +.000/-.039)
SWITCH
TERMINAL
DETAIL
VR
TERMINAL
7.0 ± 0.3
DETAIL
(.276 ± .012)
3.0 ± 0.3
(.118 ± .012)
4.0 ± 0.3
(.157 ± .012)
1.0 ± 0.3
(.039 ± .012)
2.0 ± 0.3
(.079 ± .012)
8.4 ± 0.3
(.331 ± .012)
3.6 ± 0.3
(.142 ± .012)
2.2 ± 0.3
(.087 ± .012)
18.0 ± 0.5
(.709 ± .020)
12.0 ± 0.5
(.472 ± .020)
DIA.
2.0 ± 0.3
(.079 ± .012)
3.0 ± 0.3
(.118 ± .012)
13.5 ± 1.0
(.531 ± .039)
5.0 ± 0.3
(.197 ± .012)
1
2
3
2
15.0 ± 0.5
(.591 ± .020)
3 PINOUT FOR “A” AND “B” TAPERS
1 PINOUT FOR “C” TAPER
5.0 ± 0.3
(.197 ± .012)
5.0 ± 0.3
(.197 ± .012)
2.0 ± 0.3
(.079 ± .012)
2.6 ± 0.3
(.102 ± .012)
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.