6534_12 Datasheet, PDF (1/1 Pages) Bourns Electronic Solutions – 7/8 (22 mm) Precision Potentiometer

*RoHS ^COMPLIANT
Features
■ Servo mount
■ Shaft support by front and rear precision ball bearings
■ Non-standard features and specifications available
■ Gangable up to 10 cups
6534 - 7/8 ” (22 mm) Precision Potentiometer
Electrical Characteristics¹
Standard Resistance Range....................................................................................1 K to 100 K ohms
Total Resistance Tolerance......................................................................................................... ±10 %
Independent Linearity ................................................................................................................ ±0.5 %
Effective Electrical Angle .......................................................................................................320 ° ±3 °
End Voltage .................................................... 0.1 % maximum (0.25 at 2 K ohms, 0.4 % at 1 K ohm)
Output Smoothness..................................................................................................................... 0.1 %
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Sea Level.............................................................................................................750 VAC minimum
Power Rating (Voltage Limited By Power Dissipation or 350 VAC, Whichever is Less)
+70 °C......................................................................................................................................1 watt
+125 °C....................................................................................................................................0 watt
Insulation Resistance (500 VDC) ................................................................ 1,000 megohms minimum
Resolution ................................................................................................................Essentially infinite
Environmental Characteristics¹
Operating Temperature Range ................................................................................. -40 °C to +125 °C
Storage Temperature Range .................................................................................... -65 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range ...........................±500 ppm/°C maximum
Vibration ........................................................................................................................................15 G
Wiper Bounce ........................................................................................... 0.1 millisecond maximum
Total Resistance Shift ...............................................................................................±2 % maximum
Shock.............................................................................................................................................50 G
Wiper Bounce ........................................................................................... 0.1 millisecond maximum
Rotational Life (No Load)......................................................................... 25,000,000 shaft revolutions
Total Resistance Shift .............................................................................................±10 % maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift .............................................................................................±10 % maximum
IP Rating....................................................................................................................................... IP 40
Mechanical Characteristics¹
Mechanical Angle ............................................................................................................... Continuous
Torque (Starting & Running) ........................................................... 0.18 N-cm (0.25 oz.-in.) maximum
Shaft Runout...............................................................................................0.025 mm (0.001 in.) T.I.R.
Lateral Runout ..............................................................................................0.05 mm (0.002 in.) T.I.R.
Shaft End Play..............................................................................................0.08 mm (0.003 in.) T.I.R.
Shaft Radial Play ..........................................................................................0.08 mm (0.003 in.) T.I.R.
Pilot Diameter Runout ................................................................................0.025 mm (0.001 in.) T.I.R.
Backlash ....................................................................................................................... 0.1 ° maximum
Weight ................................................................................................................................... 18 grams
Terminals ...............................................................................................................Side exit turret style
Soldering Condition
Manual Soldering.................................96.5Sn/3.0Ag/0.5Cu solid wire or no-clean rosin cored wire
370 °C (700 °F) max. for 3 seconds
Wave Soldering ........................................................ 96.5Sn/3.0Ag/0.5Cu solder with no-clean flux
260 °C (500 °F) max. for 5 seconds
Wash processes ..................................................................................................Not recommended
Marking.................................Manufacturer’s name and part number, resistance value and tolerance,
linearity tolerance, wiring diagram, and date code.
Ganging ................................................................................................................... 10 cups maximum
1_{At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.}
Product Dimensions
5.08
(.200)
MIN.
3.170 + .000/- .008
(.1248+.0000/-.0003)
DIA.
22.23
(.875)
DIA.
.25
(.010)
X
45
°
±
10
°
CHAMFER
19.050 +.000/ - .013
(.75+.0000/-.0005)
1.57
(.062)
12.07
(.475)
1.57
(.062)
(1.0.4557)MIN.
12.70 ± .79
(1/2 ± 1/32)
ADD ^5.08 FOR EACH ADDITIONAL CUP.
(.200)
1
3
120 ° MAX.
30 °
30 °
±3°
±3°
2
15.24
(.600)
MAX.
TOLERANCES: EXCEPT WHERE NOTED
DFREACCIMTIAOLNSS: _:.X±X1/±_64(..5012), .XXX ±
.13
(.005)
DIMENSIONS:
MM
(IN.)
2 ^WIPER
CCW ₁
CLOCKWISE
3 CW
Recommended Part Numbers
Part Number
6534S-1-102
6534S-1-202
6534S-1-502
6534S-1-103
6534S-1-203
6534S-1-503
6534S-1-104
Resistance
(Ω)
1,000
2,000
5,000
10,000
20,000
50,000
100,000
REV. 08/12
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications