MPI-815H Datasheet, PDF(1/1 Page) BOSER Technology Co., Ltd – 150W AC-DC ATX Open Frame Power Aupply

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

MPI-815H Datasheet, PDF (1/1 Pages) BOSER Technology Co., Ltd – 150W AC-DC ATX Open Frame Power Aupply

MPI-815H

150W AC-DC ATX Open Frame Power Aupply

2.0

4.05

9.7

8.1

6.36

8.1

Features

SCRE

*Input Voltage: 85~264VAC

Cuslomer system

*Input Frequency: 47~63Hz

*Inrush Current: The maximum inrush current is 6A at

115VAC or 3A at 230VAC

*Load Range: At the factory, the +5V output is set between

5.08~5.13V and all output at 60% rated load, and the other

output is checked to be within the accuracy range. The

Safety Standards

maximum total combined output power on the 3.3V and 5V

rails is 90W. The maximum load cannot be exceed 150W

*Safety: UL 60950 / CSA 22.2 No.234 / VDE EN60950

*Ripple And Noise: The peak to peak ripple and noise for +5V, *EMI: FCC docket 20780 cruve B / EN55022B

3.3V output are less than 50mV for +5Vsb is 100mV, for +12 V *EMS: IEC 61000-4-2 Level 3 8KV air discharge, Level 2 4KV

is less than 100mV, for -12V is less than 150mV at ranted load contact discharge / IEC 61000-4-3 Level 3 10V/M / IEC

and nominal input, which is measured by a 15MHz bandwidth

61000-4-4 Level 3 2KV / IEC 61000-4-5 Level 3 2KV /

limited oscilloscope and the each output is connected with a

IEC61000-4-6 Level 3 10V / IEC 61000-4-8 Level 3 10A/M /

0.47uF capacitor

IEC 61000-4-11

*Line Regulation: The line regulation is less than +/-1% at

*PFC: IEC 61000-3-2 / IEC 61000-3-3

rated load with +/-10% change in input voltage

*Load Regulation: The load regulation for +5V is less than +/-

2 %, for +12V is less than +/-5%, for +3.3 and -12V is less

than +/-5% while the measuring is done by changing the

measured output loading +/-40% from 60% rated load, and

keep other output is at 60% rated load

Output Min.

Voltage Load

+5V 1A

+12V 0A

-12V 0A

Rated

Load

11A

0.5A

Max. Voltage

Load Accuracy

14A 5.05~5.15V

10A 11.6~12.6V

1A -11.4~-12.6V

*Hold Up Time: The hold up time is longer than 16mS at

+3.3V 0A 7.5A 12A 3.2~3.4V

115VAC input and rated load

+5Vsb 0A 0.75A 1.5A 4.8~5.2V

*Power On/Off: The power supply will be turned on when the

power On/Off pin is connected to secondary GND

*Power Good Signal: The power is turned on, the power good

signal will go high between 100 ms to 500 ms after all output

DC voltage are within regulation limits

*Power Fail Signal: The power fail signal will go low at least

1ms before any of the output voltages fall below the regulation

limits

*Efficiency: The efficiency is higher than 70% while measuring

at nominal line and rated load

*Altitude: 0~10,000ft

*Protection: The power supply will generate the hiccup mode

to protect itself against short circuit or over load condition, and

will return to normal after wrong condition is removed. The

power supply has over voltage protection function

*Over Temp. Protection: When the power supply operating

over the temperature limit, the power supply will be shut down

automatically to protect itself

*Temperature: 0~+50oC (operating); -20~+70oC (storage)

*Humidity: 10~90% non-condensing

*Dimensions: 19.8 x 9.7 x 4.0 cm