|
HSMS-282C Datasheet, PDF (6/15 Pages) Broadcom Corporation. – Surface Mount RF Schottky Barrier Diodes | |||
|
◁ |
Thus, p-type diodes are generally reserved for detector
applications (where very high values of RV swamp out
high RS) and n-type diodes such as the HSMS-282x are
used for mixer applications (where high L.O. drive levels
keep RV low). DC biased detectors and self-biased detecâ
tors used in gain or power control circuits.
Detector Applications
Detector circuits can be divided into two types, large signal
(Pin > â20 dBm) and small signal (Pin < â20 dBm). In general,
the former use resistive impedance matching at the input
to improve flatness over frequency â this is possible since
the input signal levels are high enough to produce adeâ
quate output voltages without the need for a high Q reacâ
tive input matching network. These circuits are self-biased
(no external DC bias) and are used for gain and power
control of amplifiers.
Small signal detectors are used as very low cost receivers,
and require a reactive input impedance matching netâ
work to achieve adequate sensitivity and output voltage.
Those operating with zero bias utilize the HSMSâ 285x
family of detector diodes. However, superior performance
over temperature can be achieved with the use of 3 to 30
µA of DC bias. Such circuits will use the HSMSâ282x family
of diodes if the operating frequency is 1.5 GHz or lower.
Typical performance of single diode detectors (using
HSMSâ2820 or HSMSâ282B) can be seen in the transfer
curves given in Figures 7 and 8. Such detectors can be reâ
alized either as series or shunt circuits, as shown in Figure
11.
DC Bias
⢠The two diodes are in parallel in the RF circuit, lowering
the input impedance and making the design of the RF
matching network easier.
⢠The two diodes are in series in the output (video)
circuit, doubling the output voltage.
⢠Some cancellation of evenâorder harmonics takes place
at the input.
DC Bias
Zero Biased Diodes DC Biased Diodes
Figure 12. Voltage Doubler.
The most compact and lowest cost form of the doubler is
achieved when the HSMSâ2822 or HSMS-282C series pair
is used.
Both the detection sensitivity and the DC forward voltage
of a biased Schottky detector are temperature sensitive.
Where both must be compensated over a wide range of
temperatures, the differential detector[2] is often used.
Such a circuit requires that the detector diode and the
reference diode exhibit identical characteristics at all DC
bias levels and at all temperatures. This is accomplished
through the use of two diodes in one package, for examâ
ple the HSMSâ2825 in Figure 13. In the Avago assembly
facility, the two dice in a surface mount package are taken
from adjacent sites on the wafer (as illustrated in Figure
14). This assures that the characteristics of the two diodes
are more highly matched than would be possible through
individual testing and hand matching.
Shunt inductor provides
video signal return
Shunt diode provides
video signal return
DC Bias
RF in
RF
impedance
RM
matching
network
RL di erential
ampli er
Video out
Zero Biased Diodes DC Biased Diodes
+3V
RL
Figure 11. Single Diode Detectors.
The series and shunt circuits can be combined into a voltâ
age doubler[1], as shown in Figure 12. The doubler offers
three advantages over the single diode circuit.
Figure 13. Differential Detector.
Notes:
1. Avago Application Note 956â4, âSchottky Diode Voltage Doubler.â
2. Raymond W. Waugh, âDesigning LargeâSignal Detectors for Handsets and Base Stations,â Wireless Systems Design, Vol. 2, No. 7, July 1997, pp 42 â 48.
6
|
▷ |