HM54 Datasheet, PDF (1/3 Pages) Bi technologies – High Current Toroidal Inductors

Electrical / Environmental
R_C^o_om^H_pli^S_ant

High Current Toroidal Inductors
• Operating Temperature Range
• Temperature Rise, Maximum
• Insulation System
-40°C to +155°C
50°C
Class F, 155°C
Specifications
Part
Number
HM54-44R42VLF
HM54-44R42HLF
HM54-45R41VLF
HM54-45R41HLF
HM54-5BR51VLF
HM54-5BR51HLF
HM54-50R60VLF
HM54-50R60HLF
HM54-50R86VLF
HM54-50R86HLF
HM54-60R86VLF
HM54-60R86HLF
Inductance
100 kHz, 0.1 V
@ 0 Adc
@ ^I_sat
µH ±10%
µH Typ.
0.42
0.38
0.42
0.38
0.41
0.35
0.41
0.35
0.51
0.42
0.51
0.42
0.60
0.50
0.60
0.50
0.86
0.61
0.86
0.61
0.86
0.71
0.86
0.71
Heating ⁽¹⁾
Current ^I_sat ⁽²⁾
(Adc) (Adc)
32
32
32
32
33
33
33
33
32
42
32
42
31
32
31
32
27
27
27
27
35
41
35
41
DCR ⁽³⁾
mΩ
Max.
1.15
1.15
0.70
0.70
0.75
0.75
1.1
1.1
1.6
1.6
1.1
1.1
Dim. A
(Inch/mm)
.099/2.5
.099/2.5
.099/2.5
.099/2.5
.126/3.2
.126/3.2
.114/2.9
.114/2.9
.099/2.5
.099/2.5
.126/3.2
.126/3.2
Dim. P
(Inch/mm)
Fig.
.284/7.2
1
.228/5.8
2
.335/8.5
1
.256/6.5
2
.386/9.8
1
.284/7.2
2
.370/9.4
1
.322/8.2
2
.370/9.4
1
.322/8.2
2
.386/9.8
1
.362/9.2
2
Notes: (1) The heating current is the DC current which causes the component temperature to increase by approximately 50°C.
This current is determined by soldering the component on a typical application PCB, and then apply the current to the component for 30 minutes.
(2) ^I_sat is the saturation current at which inductance rolls off approximately 30% from its initial value.
(3) DC resistance is measured at 25°C.
Outline Dimensions (Inch/mm)
Figure 1 (Vertical Mount)
Figure 2 (Horizontal Mount)
.142±.020
3.6±0.5
P± ^.020
0.5
Body
Style
44
45
50
5B
60
Vertical Mount
Fig. L
W
Ht
1
.570 .260 .510
14.48 6.61 12.95
1
.610 .295 .510
15.50 7.50 12.95
1
.640 .300 .570
16.25 7.61 14.48
1
.690 .380 .590
17.53 9.65 14.98
1
.760 .360 .680
19.30 9.14 17.27
Horizontal Mount
Fig. L
W Ht
2
.570 .570 .260
14.48 14.48 6.61
2
.610 .610 .295
15.50 15.50 7.50
2
.640 .640 .300
16.25 16.25 7.61
2
.690 .690 .380
17.53 17.53 9.65
2
.760 .760 .360
19.30 19.30 9.14
Refer to Specifications table for ‘A’ & ‘P’ dimensions of each model.
28 MAGNETIC COMPONENTS SELECTOR GUIDE 2007/08 EDITION
We reserve the right to change specifications without prior notice.
P± ^.020
0.5
.142±.020
3.6±0.5
www.bitechnologies.com