BGS5_16 Datasheet, PDF (1/9 Pages) BeRex Corporation – 40-4000 MHz SILICON GERMANIUM Gain Block

BGS5
40-4000 MHz SILICON GERMANIUM Gain Block
Device Features
 Single Fixed 3V supply
 No Dropping Resistor Required
 No matching circuit needed
 Lead-free/Green/RoHS compliant SOT-363 package
 Application: Driver Amplifier, Cellular, PCS, GSM,
UMTS, WCDMA, Wireless Data
Part Marking (X: Wafer number)
OUT
GND
BS5X ^GND
GND
GND
IN
Pin Description
RF IN
3
RF OUT
6
GND 1,2,4,5
Product Description
BeRex’s BGS5 is a high SiGe HBT MMIC am-
plifier, internally matched to 50 Ohms with-
out the need for external components. De-
signed to run directly from a 3V supply. The
BGS5 is designed for high linearity 3V gain
block applications . It is packaged in a RoHS-
compliant with SOT-363 surface mount
package.
Applications
 Driver Amplifier
 Cellular, PCS, GSM, UMTS, WCDMA
Typical Performance¹
Parameter
70 900
Gain
17.3 16.5
S11
S22
OIP3²
-16 -17
-14 -15
32.5 31.5
P1dB
N.F
15.5 16.2
2.2 2.5
Frequency
1900 2140
15 14.6
-17 -19
-13 -14
28.5 28
15.4 15
2.7 2.8
2650
13.8
-40
-17
27
14.5
3
Unit
3500 MHz
13.3 dB
-16.3 dB
-16.9 dB
24.6 dBm
13.7 dBm
2.7 dB
1 _{Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω system.}
2 _{OIP3 _ measured with two tones at an output of 0 dBm per tone separated by 1 MHz.}
Applications Circuit
Freq.
C1/C2
L1
(1608 Chip Ind.)
Application Circuit Values Example
70~900MHz 900MHz ~ 3GHz
2nF
100pF
1uH
56nH
3GHz ~ 4GHz
10pF
12nH
C3 C4 C5
+3V
Bandwidth
I_C @ (Vc = 3V)
V_C
dG/dT
R_TH
Min.
Typical Max.
Unit
40
4000
MHz
46
52
58
mA
3.0
V
-0.001
dB/°C
130
°C/W
RFin
C1
L1
BGS5
Absolute Maximum Ratings
Parameter
Rating
Unit
C2
RFout _{Operating Case Temperature}
-40 to +105
°C
Storage Temperature
-55 to +155
°C
Junction Temperature
150
°C
*C1, C2, C3 =100 pF ± 5%; C4 = 1000 pF ± 5%; C5 = 10uF; **L1 = 56nH ^{Operating Voltage}
+3.5
V
**less than 56nH improves RF performance at over 0.5GHz.
Supply Current
110
mA
*820nH or higher value L1 improves RF performance at under 500MHz. ^{Input RF Power}
15
dBm
*Optimum value of L1 may vary with board design.
Operation of this device above any of these parameters may result in permanent damage.
*C1,C2=2000pF, L1=820nH for 50MHz application.
*C1,C2=10pF, L1=12nH for 3.5GHz application.
BeRex
●website: www.berex.com
●email: [e-mail]
1
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E