AZ6962 Datasheet, PDF (1/3 Pages) ZETTLER Electronics – 10 AMP SUBMINIATURE POWER RELAY

AZ6962
10 AMP SUBMINIATURE
POWER RELAY
FEATURES
• High sensitivity, 120 mW pickup
• Dielectric strength 5000 Vrms
• Isolation spacing greater than 10 mm
• 10kV surge voltage
• Proof tracking index (PTI/CTI) 250
• 10 Amp switching capability
• Epoxy sealed
• UL, CUR file E43203
• VDE file 40010953
CONTACTS
Arrangement
SPDT (1 Form C), DPDT (2 Form C)
SPST (1 Form A)
Ratings
Resistive load:
Max. switched power: 240 W or 2500 VA
(2 Form C: 150 W or 1250 VA)
Max. switched current: 10 A
(2 Form C: 5 A)
Max. switched voltage: 240 VDC* or 440 VAC
Rated Load
UL, CUR
VDE
Material
* Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
10 A at 250 VAC resistive, 30k cycles (1 Form C)
10 A at 30 VDC resistive, 30k cycles (1 Form C)
B300, R300 Pilot Duty (1 Form C)
1/2 HP at 240 VAC, 30k cycles (N.O.)
1/3 HP at 120 VAC, 30k cycles (N.O.)
5 A at 250 VAC resistive, 30k cycles
(2 Form C)
8 A at 250 VAC resistive, 100k cycles
(1 Form A, and 1 Form C)
Silver tin oxide
COIL
Power
At Pickup Voltage
(typical)
Max. Continuous
Dissipation
Temperature Rise
120 mW (up to 24 VDC coil) (1 pole)
140 mW (48 VDC and 60 VDC coil)
(1 pole)
176 mW (2 pole)
1.2 W at 20°C (68°F) ambient
20°C (36°F) at nominal coil voltage
Temperature
Max. 105°C (221°F)
GENERAL DATA
Life Expectancy
Mechanical
Electrical
Minimum operations
3 x 10⁷
1 x 10⁵ at 8 A 250 VAC res.
Operate Time (typical) 7 ms at nominal coil voltage
Release Time (typical) 3 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
5000 Vrms coil to contact
(at sea level for 1 min.) 2500 Vrms between contact sets
1500 Vrms between open contacts
Insulation
Resistance
1000 megohms min. at 20°C, 500 VDC,
50% RH
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature At nominal coil voltage
Operating
-40°C (-40°F) to 85°C (185°F)
Storage
-40°C (-40°F) to 105°C (221°F)
Vibration
Shock
Break Contact: 5 g at 10 …500 Hz
Make Contact: 20 g at 10…500 Hz
10 g
Enclosure
P.B.T. polyester, UL94 V-O
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp. 80°C (176°F)
Max. Immersion Time 30 seconds
Weight
8 grams
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
9/27/06W