05045C821KAT1A Datasheet, PDF (39/48 Pages) AVX Corporation – Multilayer Ceramic Chip Capacitor

Embossed Carrier Configuration
8 & 12 mm Tape Only
8 & 12 mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
8mm
and
12mm
D₀
8.4
+0.10
-0.0
(.059
) ^+.004
-0.0
E
P₀
P₂
1.75 ± 0.10 4.0 ± 0.10 2.0 ± 0.05
(.069 ± .004) (.157 ± .004) (.079 ± .002)
T Max.
0.600
(.024)
VARIABLE DIMENSIONS
Tape Size
B₁
D₁
F
Max.
Min.
See Note 6 See Note 5
P₁
R
Min.
See Note 2
8mm
4.55
(.179)
1.0
(.039)
3.5 ± 0.05 4.0 ± 0.10
(.138 ± .002) (.157 ± .004)
25
(.984)
12mm
8.2
(.323)
1.5
(.059)
5.5 ± 0.05 4.0 ± 0.10
(.217 ± .002) (.157 ± .004)
30
(1.181)
T₁
0.10
(.004)
Max.
G₁
0.75
(.030)
Min.
See Note 3
T₂
W
2.5 Max
(.098)
8.0
+0.3
-0.1
(.315
+.012
-.004
)
6.5 Max. 12.0 ± .30
(.256) (.472 ± .012)
G₂
0.75
(.030)
Min.
See Note 4
A₀ B₀ K₀
See Note 1
See Note 1
8mm
1/2 Pitch
4.55
(.179)
1.0
(.039)
3.5 ± 0.05 2.0 ± 0.10
(.138 ± .002) 0.79 ± .004
25
(.984)
2.5 Max.
(.098)
8.0
+0.3
-0.1
(.315
+.012
-.004
)
See Note 1
12mm
Double
Pitch
8.2
(.323)
1.5
(.059)
5.5 ± 0.05 8.0 ± 0.10
(.217 ± .002) (.315 ± .004)
30
(1.181)
6.5 Max. 12.0 ± .30 _{See Note 1}
(.256) (.472 ± .012)
NOTES:
1. A0, B0, and K0 are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The
clearance between the end of the terminals or body of the component to the sides and depth of the cavity (A0, B0, and K0) must be within 0.05 mm (.002) min. and 0.50 mm
(.020) max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches C & D).
2. Tape with components shall pass around radius “R” without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for 12 mm
embossed tape for reels with hub diameters approaching N min. (Table 4).
3. G₁ dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavi-
ty whichever is less.
4. G₂ dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or
to the edge of the cavity whichever is less.
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the emboss-
ment. Dimensions of embossment location and hole location shall be applied independent of each other.
6. B₁ dimension is a reference dimension for tape feeder clearance only.
37