HCPL-3101-000E Datasheet, PDF (7/14 Pages) AVAGO TECHNOLOGIES LIMITED – Power MOSFET/IGBT Gate Drive Optocouplers

Switching Specifications (T_A = 25°C)
Parameter
Sym.
Device Min. Typ.
Propagation
Delay Time to
High Output
Level
t_PLH
HCPL-3100 -
1
HCPL-3101 - 0.3
Propagation
Delay Time to
Low Output
Level
t_PHL
HCPL-3100 -
1
HCPL-3101 - 0.3
Rise Time
t_r
HCPL-3100 - 0.2
HCPL-3101
Fall Time
t_f
HCPL-3100 - 0.2
HCPL-3101
Output High
Level Common
Mode Transient
Immunity
|CM_H| HCPL-3100 15
HCPL-3101
Output Low
|CM_L|
15
Level Common
Mode Transient
Immunity
Max. Units
2
µs
0.5 µs
2
µs
0.5 µs
Test Conditions
I_F = 10 mA
I_F = 5 mA
I_F = 10 mA
V_CC = 24 V,
V_O1 = 24 V,
R_G = 47 Ω,
C_G = 3000 pF
I_F = 5 mA
0.5 µs I_F = 10 mA
I_F = 5 mA
0.5 µs I_F = 10 mA
I_F = 5 mA
- kV/µs I_F = 10 mA
I_F = 5mA
- kV/µs I_F = 0 mA
V_CM = 1500 V
(peak),
V_CC = 24 V
V_O1 = 24 V
∆V_02H = ∆V_02L
= 2.0 V
Fig. Note
9, 2, 6
25,
26,
27
10 2
Packaging Characteristics
Parameter
Input-Output Momentary
Withstand Voltage*
Resistance (Input-Output)
Capacitance (Input-Output)
Sym.
V_ISO
Min. Typ.
5000
R_I-O
5x10¹⁰ 10¹¹
C_I-O
–
1.2
Max.
Units
V rms
–
Ω
–
pF
Test Conditions
RH = 40% to 60%
t = 1 min, T_A = 25°C
V_I-O = 500 V, T_A = 25°C
RH = 40% to 60%
f = 1 MHz
Fig. Note
4, 5
4
4
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification, or Avago Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 11 and 12.
2. A bypass capacitor of 0.01 µF or more is needed near the device between V_CC and GND when measuring output and transfer
characteristics.
3. I_FLH represents the forward current when the output goes from low to high.
4. Device considered a two terminal device; pins 1-4 are shorted together and pins 5-8 are shorted together.
5. For devices with minimum V_ISO specified at 5000 V rms, in accordance with UL 1577, each optocoupler is proof-tested by
applying an insulation test voltage ≥ 6000 V rms for one second (leakage current detection limit, I_I-O ≤ 200 µA).
6. The t_PLH and t_PHL propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
7. R₂ limits the Q1 and Q2 peak currents. For more applications and circuit design information see Application Note “Power
Transistor Gate/Base Drive Optocouplers.”
7