HCPL-M452 Datasheet, PDF (6/9 Pages) Agilent(Hewlett-Packard) – Small Outline, 5 Lead, High Speed Optocouplers

Switching Specifications
Over recommended temperature (T_A = 0°C to 70°C) V_CC = 5 V, I_F = 16 mA unless otherwise specified.
Parameter
Symbol Device Min. Typ.* Max. Units Test Conditions
Fig.
Note
Propagation Delay t_PHL
Time to Logic Low
at Output
0.2
0.8
Ps
1.0
T_A = 25°C
R_L = 1.9 k: 5, 6, 10 9
Propagation Delay t_PLH
Time to Logic High
at Output
Common Mode
|CM_H| HCPL-
Transient Immunity
M452
at Logic High Level
Output
HCPL- 15
M453
Common Mode
Transient Immunity
at Logic Low Level
Output
|CM_L|
Bandwidth
BW
All typicals at T_A = 25°C.
HCPL-
M452
HCPL- 15
M453
0.6
0.8
1.0
T_A = 25°C
R_L = 1.9 k: 5, 6, 10 9
1
kV/Ps V_CM = 10 V_p-p I_F = 0 mA
11
8, 9
T_A = 25°C
30
V_CM = 1500 ^{RL = 1.9 k:}
V_p-p
1
V_CM = 10 V_p-p I_F = 16 mA 11
8, 9
T_A = 25°C
30
V_CM = 1500 ^{RL = 1.9 k:}
V_p-p
3
MHz R_L = 100 :, See Test Circuit 8, 9
10
Notes:
1. Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C.
2. Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C.
3. Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C.
4. Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I_O, to the forward LED input current, I_F, times 100.
6. Device considered a two terminal device: pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted together.
7. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V_RMS for 1 second (leakage detection
current limit, I_I-O ≤ 5 PA).
8. Common transient immunity in a Logic High level is the maximum tolerable (positive) dV_CM/dt on the rising edge of the common mode pulse, V_CM,
to assure that the output will remain in a Logic High state (i.e., V_O > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum
tolerable (negative) dV_CM/dt on the falling edge of the common mode pulse signal, V_CM to assure that the output will remain in a Logic Low state
(i.e., V_O < 0.8 V).
9. The 1.9 k: load represents 1 TTL unit load of 1.6 mA and the 5.6 k: pull-up resistor.
10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
11. Use of a 0.1 PF bypass capacitor connected between pins 4 and 6 is recommended.
6