ACPL-K43T-060E Datasheet, PDF (6/11 Pages) AVAGO TECHNOLOGIES LIMITED – Automotive R2CouplerTM Wide Operating Temperature

Switching Specifications (AC)
Over recommended operating (T_A = -40° C to 125° C), V_CC = 5.0 V unless otherwise specified.
Parameter
Symbol Min Typ Max Units Test Conditions
Propagation Delay t_PHL
Time to Logic Low
at Output
Propagation Delay t_PLH
Time to Logic High
at Output
Pulse Width
Distortion
PWD
Propagation Delay PDD
Difference Between
Any 2 Parts
Common Mode
|CM_H|
Transient Immunity
at Logic High Output
0.07 0.15 0.8 s
0.06
1.0
0.7 5
T_A = 25° C
I_F = 10 mA,
R_L = 1.9 k
I_F = 1.5 mA,
R_L = 10 k
Pulse: f = 10 kHz,
Duty cycle = 50%,
V_CC = 5.0 V, C_L = 15 pF,
V_THHL = 1.5 V
1 10
I_F = 0.8 mA,
R_L = 27 k
0.15 0.5 0.8 s
0.03
1.0
0.9 5
T_A = 25° C
I_F = 10 mA,
R_L = 1.9 k
I_F = 1.5 mA,
R_L = 10 k
Pulse: f = 10 kHz,
Duty cycle = 50%,
V_CC = 5.0 V, C_L = 15 pF,
V_THHL = 2.0 V
2 10
I_F = 0.8 mA,
R_L = 27 k
0.35 0.45 s
0.85
T_A = 25° C
Pulse: f = 10 kHz, Duty cycle = 50%,
I_F = 10 mA, V_CC = 5.0 V, R_L = 1.9 k,
C_L = 15 pF, V_THHL = 1.5 V,
V_THLH = 2.0 V
0.35 0.5 s
0.9
T_A = 25° C
Pulse: f = 10 kHz, Duty cycle = 50%,
I_F = 10 mA, V_CC = 5.0 V, R_L = 1.9 k,
C_L = 15 pF, V_THHL = 1.5 V,
V_THLH = 2.0 V
15 30
kV/s I_F = 0 mA V_CM = 1500 V_p-p, R_L = 1.9 k,
V_CC = 5 V, T_A = 25° C
Common Mode
|CM_L| 15 30
Transient Immunity
at Logic Low Output
kV/s I_F = 10 mA
Common Mode
|CM_H|
5
Transient Immunity
at Logic High Output
kV/s I_F = 0 mA V_CM = 1500 V_p-p, R_L = 10 k,
V_CC = 5 V, T_A = 25° C
Common Mode
|CM_L|
5
Transient Immunity
at Logic Low Output
kV/s I_F = 1.5 mA
Fig. Note
5, 6, 7, 2, 3
8, 9, 10,
13
5, 6, 7, 2, 3
8, 9, 10,
13
2, 3, 4
2, 3, 5
14
6
14
6
Package Characteristics
Parameter
Symbol Min. Typ. Max. Units Test Conditions
Fig. Note
Input-Output Momentary
Withstand Voltage^*
Input-Output Resistance
V_ISO
5000
R_I-O
10¹⁴
V_RMS RH ≤ 50%, t = 1 min.,
7, 8
T_A = 25° C

V_I-O = 500 Vdc
7
Input-Output Capacitance
C_I-O
0.6
pF
f = 1 MHz, V_I-O = 0 Vdc
7
* The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating.
Notes:
1. Current Transfer Ratio in percent is defined as the ratio of output collector current, I_O, to the forward LED input current, I_F, times 100.
2. Use of a 0.1 F bypass capacitor connected between pins 5 and 8 is recommended.
3. The 1.9 k load represents 1 TTL unit load of 1.6 mA and the 5.6 k pull-up resistor.
4. Pulse Width Distortion (PWD) is defined as |t_PHL – t_PLH| for any given device.
5. The difference between t_PLH and t_PHL between any two parts under the same test condition.
6. Common transient immunity in a Logic High level is the maximum tolerable (positive) dV_CM/dt on the rising edge of the common mode pulse, V_CM,
to assure that the ouput will remain in a Logic High state (i.e., V_O > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum
tolerable (negative) dV_CM/dt on the falling edge of the common mode pulse signal, V_CM to assure that the output will remain in a Logic Low state
(i.e., V_O < 0.8 V).
7. Device considered a two terminal device: pins 1, 2, 3 and 4 shorted together, and pins 5, 6, 7 and 8 shorted together.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V_RMS for 1 second.
6