HFBR-RUS100Z Datasheet, PDF (4/11 Pages) AVAGO TECHNOLOGIES LIMITED – Plastic Optical Fiber Cable and Accessories for Versatile Link

Plastic Optical Fiber Connector Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Unit
Note
Storage and Operating Temperature
Recommended Operating Temperature
Installation Temperature
Nut Torque
HFBR-4505Z/4515Z Adapter
T_S,O
-40
85
°C
1
T_O
-40
85
°C
1
T_l
0
70
°C
1
T_N
0.7
N-m
2
100
OzF-in.
Notes:
1. Storage and Operating Temperatures refer to the ranges over which the connectors can be used when not subjected to mechanical stress.
Installation Temperature refers to the ranges over which connectors may be installed onto the fiber and over which connectors can be connected
and disconnected from transmitter and receiver modules.
2. Recommended nut torque is 0.57 N-m.
Plastic Optical Fiber Connector Mechanical/Optical Characteristics
T_A = -40 to +85°C, Unless Otherwise Specified.
Parameter
Retention Force,
Connector to
Versatile Link
Transmitters and
Receivers
Part Number
Simplex,
HFBR-4501Z/4511Z
Simplex Latching,
HFBR-4503Z/4513Z
Duplex,
HFBR-4506Z
Symbol Min. Typ.^[1] Max.
F_R-C
7
8
3
47 80
11
7 12
4
Units
N
Temp. °C Note
+25
2
-40 to +85
+25
-40 to +85
+25
-40 to +85
Duplex Latching,
HFBR-4516Z
50 80
15
+25
-40 to +85
Tensile Force,
Simplex,
F_T
8.5 22
N
3
Connector to Cable
HFBR-4501Z/4511Z
Simplex Latching,
HFBR-4503Z/4513Z
8.5 22
Duplex, HFBR-4506Z
14 35
Adapter Connector
to Connector Loss
Duplex Latching,
HFBR-4516Z
HFBR-4505Z/4515Z with α_CC
HFBR-4501Z/4511Z
14 35
0.7 1.5
2.8 dB
25
4, 5
Retention Force
HFBR-4505Z/4515Z with F_R-B
7
8
N
Connector to Adapter HFBR-4501Z/4511Z
Insertion Force,
Simplex,
F_I
8
30 N
6
Connector to Versatile HFBR-4501Z/4511Z
Link Transmitters and
Receivers
Simplex Latching,
HFBR-4503Z/4513Z
16
35
Duplex, HFBR-4506Z
13
46
Duplex Latching
HFBR-4516Z
22
51
Notes:
1. Typical data are at +25°C.
2. No perceivable reduction in retention force was observed after 2000 insertions. Retention force of non-latching connectors is lower at elevated
temperatures. Latching connectors are recommended for applications where a high retention force at high temperatures is desired.
3. For applications where frequent temperature cycling over temperature extremes is expected, please contact Avago Technologies for alternate
connectoring techniques.
4. Minimum and maximum limit for α_CC for 0°C to +70°C temperature range. Typical value of α_CC is at +25°C.
5. Factory polish or field polish per recommended procedure.
6. Destructive insertion force was typically at 178 N (40 lb.).
4