AJAV-5505 Datasheet, PDF (3/6 Pages) AVAGO TECHNOLOGIES LIMITED – W-CDMA/HSPA Band V Power Amplifier

Table 4. Electrical Specifications ^[1] (continued)
Parameter
Adjacent Channel Leakage Ratio ^[2,4]
Noise ^[14]
Error Vector Magnitude ^[2,4,5]
Power Added Efficiency ^[2,5,6]
Quiescent Idle Current
Average Current ^[2,5,7]
Powerdown Current ^[4,8]
Logic Current ^[4,9]
Input Impedance ^[5]
Reverse Intermodulation ^[4,5,10]
Harmonics ^[2,4,5]
Instantaneous Phase Change ^[4,5,15]
Coupling Factor ^[11]
Daisy Chain Insertion Loss ^[5]
Daisy Chain Return Loss ^[5,11]
Output Power Error ^[5,12]
Turn-on Time ^[13]
Turn-off Time ^[5,13]
Other Spurious ^[4,5]
Ruggedness ^[5]
Symbol Condition
Min.
ACLR1 ± 5 MHz offset
-
ACLR2 ^[5] ± 10 MHz offset
-
N
RX Band, 45 MHz offset
-
GPS Band, 1524 – 1577 MHz
-
ISM Band, 2400 – 2484 MHz
-
EVM
P_OUT ≤ P_MAX
-
PAE
HP mode
-
MP mode
-
I_CQ
LP mode
-
I_AVG
Total current from all pins
-
I_PD
VEN = V_IL
-
I_CTRL
-
Z_IN
-
± 5 MHz offset
-
± 10 MHz offset
-
2F₀
Second harmonic
-
3F₀, 4F₀ Third and fourth harmonic
-
LP mode ↔ MP mode
-
MP mode ↔ HP mode
-
s31
-
s34
UMTS Band V
-
UMTS Band I, II
-
s33, s44 UMTS Band V
-
UMTS Band I, II
-
Load VSWR = 2.5:1
-1
T_ON
-
T_OFF
-
Load VSWR ≤ 5:1
-
No permanent damage or degradation -
Typ.
-42
-53
-140
-164
-164
1.5
40
27
3.5
19
5
5
1.4:1
-
-
-
-
90
50
-20
-0.7
-1.1
-27
-20
-
12
8
-
-
Max. Unit
-38 dBc
-48 dBc
-
dBm/Hz
-
dBm/Hz
-
dBm/Hz
3.35 %
-
%
-
%
-
mA
-
mA
10
mA
10
mA
2.5:1 VSWR
-31 dBc
-41 dBc
-35 dBc
-35 dBc
-
degree (°)
-
degree (°)
-
dB
-
dB
-
dB
-
dB
-
dB
+1
dB
15
ms
10
ms
-70 dBc
10:1 VSWR
Notes:
1. Specifications at nominal operating conditions V_IH = 1.8 V, VEN = 1.8 V, VBAT = 3.8 V, T_A = 25 °C, RF ports at 50 Ω, guaranteed over the full range of
operating frequency and guaranteed by production test unless indicated otherwise.
2. Specification is guaranteed using W-CDMA modulation RMC (12.2 kbps) in compliance with 3GPP Release 99.
3. RX band gain is specified relative to PA gain at 836.5 MHz.
4. Specification is guaranteed over all power modes given in Table 3.
5. Specification is guaranteed by characterization.
6. Power-Added Efficiency (PAE) includes total current consumption through all pins while PA is operating at maximum linear output power.
7. Calculated using three power modes (HP, MP, LP) with handset W-CDMA transmitter power distribution in GSMA DG.09 specification assuming 3
dB of post-PA loss.
8. Total supply current measured when the PA is disabled.
9. Specification applies to each VEN, VM0, and VM1 pin.
10. Interferer is CW at a relative power level of -40 dBc and offset from the W-CDMA modulated carrier.
11. Measured at CPLO pin.
12. Power variation measured at the RFO pin across 8 phase angles while power at CPLO pin is held constant.
13. Specified from the start of the PA enable transition to when the output power is within ±1 dB of final value.
14. Specification is guaranteed by characterization at P_MAX.
15. Phase change should be measured at the center channel at each switch point and compensated in the baseband.
3