AFCT-701SDDZ Datasheet, PDF (2/20 Pages) AVAGO TECHNOLOGIES LIMITED – 10Gb/1Gb Ethernet, 1310nm SFP+ Transceiver

Description, continued
Installation
The AFCT-701SDDZ transceiver package is compliant
with the SFF 8432 Improved Pluggable Formfactor hous-
ing specification for the SFP+. It can be installed in any
INF-8074 or SFF-8431/2 compliant Small Form Pluggable
(SFP) port regardless of host equipment operating status
The AFCT-701SDDZ is hot-pluggable, allowing the mod-
ule to be installed while the host system is operating and
on-line. Upon insertion, the transceiver housing makes
initial contact with the host board SFP cage, mitigating
potential damage due to Electro-Static Discharge (ESD).
By selecting TX rate select to 1.25 Gbps operation, the TX
module performance complies with the extinction ratio
and output power level in the 1000BASE-LX specifica-
tions.
Likewise RX performance complies with the sensitivity
performance in the 1000BASE-LX by selecting RX rate
select to 1.25 Gbps operation.
The rate select can be done through either the hardware
pins or the software access to the A2h page of EEPROM
map. The user can refer to the Appendix for details of
rate select.
Digital Diagnostic Interface and Serial Identification
The two-wire interface protocol and signaling detail are
based on SFF-8431. Conventional EEPROM memory,
bytes 0-255 at memory address 0xA0, is organized in
compliance with SFF-8431. New digital diagnostic in-
formation, bytes 0-255 at memory address 0xA2, is
compliant to SFF-8472. The new diagnostic information
provides the opportunity for Predictive Failure Identifi-
cation, Compliance Prediction, Fault Isolation and Com-
ponent Monitoring.
Predictive Failure Identification
The AFCT-701SDDZ predictive failure feature allows a
host to identify potential link problems before system
performance is impacted. Prior identification of link
problems enables a host to service an application via
“fail over” to a redundant link or replace a suspect de-
vice, maintaining system uptime in the process. For ap-
plications where ultra-high system uptime is required, a
digital SFP provides a means to monitor two real-time
laser metrics associated with laser degradation and pre-
dicting failure: average laser bias current (Tx_Bias) and
average laser optical power (Tx_Power).
Compliance Prediction
Compliance prediction is the ability to determine if an
optical transceiver is operating within its operating and
environmental requirements. AFCT-701SDDZ devices
provide real-time access to transceiver internal supply
voltage and temperature, allowing a host to identify
potential component compliance issues. Received
optical power is also available to assess compliance of
a cable plant and remote transmitter. When operating
out of requirements, the link cannot guarantee error free
transmission.
Fault Isolation
The fault isolation feature allows a host to quickly pin-
point the location of a link failure, minimizing down-
time. For optical links, the ability to identify a fault at a
local device, remote device or cable plant is crucial to
speeding service of an installation. AFCT-701SDDZ real-
time monitors of Tx_Bias, Tx_Power, Vcc, Temperature
and Rx_Power can be used to assess local transceiver
current operating conditions. In addition, status flags
TX_DISABLE and Rx Loss of Signal (LOS) are mirrored in
memory and available via the two-wire serial interface.
Component Monitoring
Component evaluation is a more casual use of the AFCT-
701SDDZ real-time monitors of Tx_Bias, Tx_Power, Vcc,
Temperature and Rx_Power. Potential uses are as de-
bugging aids for system installation and design, and
transceiver parametric evaluation for factory or field
qualification. For example, temperature per module can
be observed in high density applications to facilitate
thermal evaluation of blades, PCI cards and systems.
2