AFBR-703SDDZ Datasheet, PDF (10/22 Pages) AVAGO TECHNOLOGIES LIMITED – Typical power dissipation 600mW

Table 5. Low Speed Signal Electrical Characteristics
The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted.
Typical values are for Tc = 40°C. VccT and VccR = 3.3 V.
Parameter
Symbol Minimum
Typical Maximum
Unit  Notes
Module Supply Current
I_CC
180
289
Power Dissipation
P_DISS
600
1000
TX_FAULT, RX_LOS
I_OH
- 50
+ 37.5
 
V_OL
- ^{0.3 0.4}
TX_DISABLE
V_IH
2.0
VccT + 0.3
 
V_IL
-0.3
0.8
Notes:
1.  Supply current includes both VccT and VccR connections.
2.  Measured with a 4.7 kΩ load to VccHost.
3.  TX_DISABLE has an internal 4.7 kΩ to 10 kΩ pull-up to VccT
mA Note 1
mW
mA Note 2
V 
V
Note 3
V
Table 6. High Speed Signal Electrical Characteristics
The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted.
Typical values are for Tc = 40°C. VccT and VccR = 3.3 V.
Parameter
Symbol Minimum Typical Maximum Unit
Notes
Tx Input Differential Voltage (TD +/-)
V_I
180
Tx Input AC Common Mode Voltage Tolerance
1200
15
mVpp
mV(RMS)
Note 1
Tx Input Differential S-parameter (100 Ω Ref.) SDD11
Note 3 dB
0.01-11.1GHz
Tx Input Differential to Common
Mode Conversion (25 Ω Ref.)
SCD11
-10
dB
0.01-11.1 GHz
Rx Output Differential Voltage (RD +/-)
Vo
300
850
mVpp

Note 1, 10 GBd
1.25 Gbd
Rx Output Termination Mismatch @ 1MHz
DZ_m 5
%
Rx Output AC Common Mode Voltage
7.5
mV(RMS) Note 5
Rx Output Output Rise and Fall Time
(20% to 80%)
tr, tf
28
ps
Rx Output Total Jitter
TJ

0.70
0.332
Ulp-p
Ulp-p
Note 6, 10 GBd
1.25 Gbd
Rx Output 99% Jitter
DJ
0.42
Ulp-p
Note 6
Rx Output Differential S-parameter (100 Ω Ref.) SDD22
Note 4 dB
0.01-11.1GHz
Rx Output Common Mode Reflection
SCC22
-6
dB
0.01-2.5 GHz
Coefficient (25 Ω Ref.)
-3
dB
2.5-11.1 GHz
Receiver Output Eye Mask
See Figure 5a
Notes:
1.  Internally AC coupled and terminated (100 Ohm differential).
2.  Internally AC coupled but requires an external load termination (100 Ohm differential).
3.  Maximum reflection coefficient is expressed as SDD11=Max(-12+2*sqrt(f ) , -6.3+13*log10(f/5.5)), for f in GHz.
4.  Maximum reflection coefficient is expressed as SDD22=Max(-12+2*sqrt(f ) , -6.3+13*log10(f/5.5)), for f in GHz.
5.  The RMS value is measured by calculating the standard deviation of the histogram for one UI of the common mode signal.
6. TJ conditions per SFF-8431.
10