AFCT-701SDDZ_15 Datasheet, PDF (1/20 Pages) AVAGO TECHNOLOGIES LIMITED – SFP+ Transceiver

AFCT-701SDDZ
10Gb/1Gb Ethernet, 1310nm
SFP+ Transceiver
Data Sheet
AFCT-701SDDZ
Description
The Avago AFCT-701SDDZ transceiver is part of a fam-
ily of SFP+ products. This transceiver utilizes Avago’s
1310nm DFB and PIN Detector technology to provide an
IEEE 10Gb Ethernet design compliant with the 10GBASE-
LR standard and allows for the operation at 1.25GBd for
Gigabit Ethernet Applications. The AFCT-701SDDZ trans-
ceiver has the signal and the chassis SFP grounds tied
together to enhance the EMI shielding performance of
the module, providing extra margin that is particularly
useful in higher density applications. The design is based
on the new electrical and mechanical specification en-
hancements to the well known SFP specifications de-
veloped by the SFF Committee. These specifications are
referred to as SFP+ to recognize these enhancements to
previous SFP specifications used for lower speed prod-
ucts. Avago Technologies is an active participant in the
SFF Committee specification development activities.
Related Products
x AFBR-703SDDZ SFP+ 10Gb/1Gb Gigabit Ethernet
10GBASE-SR transceiver for operation in OM3 MMF
link applications with link length up to 300 meters
x AFCT-701SDZ(AFCT-701ASDZ) SFP+ 10 Gigabit
Ethernet 10GBASE-LR transceiver with case
temperature 0-70 qC (0-85 qC) for operation in SMF
link applications with link lengths up to 10 Km.
x AFBR-707SDZ SFP+ 10 Gigabit Ethernet 10GBASE-
LRM transceiver for 220 meter operation in all MMF
link applications including OM1 and OM2 legacy fiber
cables and new high bandwidth OM3 fiber cables.
x AFCT-5016Z SFP+ Evaluation Board The purpose of
this SFP+ evaluation board is to provide the designer
with a convenient means for evaluating SFP+ fiber
optic transceivers.
Features
x Avago 1310nm Distributed Feedback (DFB) source
and Transmitter Optical Subassembly technology
x Avago PIN detector and Receiver Optical Subassembly
technology
x Typical power dissipation 850mW
x Full digital diagnostic management interface
x Avago SFP+ package design enables equipment EMI
performance in high port density applications with
margin to Class B limits
x Flexibility in data rate selection through either
hardware or software control
Specifications
x Optical interface specifications per IEEE 802.3ae
10GBASE-LR
x Compliant to the transmitter extinction ratio and
the receiver sensitivity specs per IEEE 802.3 Gigabit
Ethernet (1.25GBd) 1000BASE-LX
x Electrical interface specifications per SFF Committee
SFF 8431 Specifications for Enhanced 8.5 and 10
Gigabit Small Form Factor Pluggable Module “SFP+”
x Management interface specifications per SFF Com-
mittee SFF 8431 and SFF 8472 Diagnostic Monitoring
Interface for Optical Transceivers
x Mechanical specifications per SFF Committee SFF
8432 Improved Pluggable Formfactor “IPF”
x LC Duplex optical connector interface confirming to
ANSI TIA/EA 604-10 (FOCIS 10A)
x Compliant to Restriction on Hazardous Substances
(RoHS) per EU and China requirements
x Compliant to halogen free requirement
x Class 1 Eye safe per requirements of IEC 60825-1/
CDRH