ACPL-M50L-500E Datasheet, PDF (1/16 Pages) AVAGO TECHNOLOGIES LIMITED – Low Power, 1MBd Digital Optocoupler

ACPL-M50L, ACPL-054L, ACPL-W50L and ACPL-K54L
Low Power, 1MBd Digital Optocoupler
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The ACPL-M50L (single-channel in SO-5 footprint),
ACPL-054L (dual-channel in SO-8 footprint), ACPL-W50L
(single-channel in stretched SO-6 footprint) and ACPL-
K54L (dual-channel in stretched SO-8 footprint) are low
power, low-input current, 1MBd digital optocouplers.
This digital optocouplers use an insulating layer between
the light emitting diode and an integrated photon detector
to provide electrical insulation between input and output.
Separate connections for the photodiode bias and output
transistor collector increase the speed up to a hundred
times over that of a conventional photo-transistor coupler
by reducing the base-collector capacitance.
The ACPL-M50L/054L/W50L/K54L have an increased com-
mon mode transient immunity of 15kV/s minimum at
V_CM = 1500V over a temperature range of -40 to 105°C.
The current transfer ratio (CTR) is 140% typical for ACPL-
M50L or 130% typical for ACPL-054L/W50L/K54L at I_F
= 3mA. This digital optocoupler can be use in any TTL/
CMOS, TTL/LSTTL or wide bandwidth analog applications.
Features
 Wide supply voltage Vcc: 2.7V to 24V
 Low Drive Current: 3mA
 Open-Collector Output
 TTL compatible
 Compact SO-5, SO-8, stretched SO-6 and stretched
SO-8 package
 15 kV/s High Common-Mode Rejection at V_CM = 1500 V
 Guaranteed performance from Temperature Range:
-40°C to +105°C
 Low Propagation Delay: 1s max at 5V
 Worldwide Safety Approval:
(Pending except ACPL-M50L)
– UL1577 recognized,
3750Vrms/1min for ACPL-M50L/054L,
5000Vrms/1min for ACPL-W50L/K54L,
– CSA Approval
– IEC 60747-5-5, IEC/EN/DIN EN 60747-5-2
Functional Diagram
Anode 1
Cathode 3
6 V_CC
5 VO
4 GND
ACPL-M50L
Anode ₁
NC 2
Cathode 3
6 ^VCC
5 V_O
4 GND
ACPL-W50L
Applications
 Communications Interface
 Digital Signal Isolation
 Micro-controller Interface
 Feedback Elements in Switching Power Supplies
 Digital isolation for A/D, D/A conversion Digital field
Anode1 1
8 VCC
Truth Table
Cathode1 2
Cathode2 3
Anode2 4
7 VO1
6 V_O2
5 GND
LED
Vo
ON LOW
OFF HIGH
ACPL-054L/K54L
The connection of a 0.1 F bypass capacitor between pins 4 and 6 for
ACPL-M50L/W50L and between pins 5 and 8 for ACPL-054L/K54L is
recommended.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.