ACPL-H342 Datasheet, PDF (1/19 Pages) AVAGO TECHNOLOGIES LIMITED – 2.5 Amp Output Current IGBT Gate Drive Optocoupler with Active Miller Clamp, Rail-to-Rail Output Voltage and UVLO in Stretched SO8

ACPL-H342 and ACPL-K342
2.5 Amp Output Current IGBT Gate Drive Optocoupler
with Active Miller Clamp, Rail-to-Rail Output Voltage
and UVLO in Stretched SO8
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
Features
The ACPL-H342/ACPL-K342 contains an AlGaAs LED,
which is optically coupled to an integrated circuit with a
power output stage. This optocoupler is ideally suited for
driving power IGBTs and MOSFETs used in motor control
inverter applications. The high operating voltage range of
the output stage provides the drive voltages required by
gate controlled devices. The voltage and high peak output
current supplied by this optocoupler make it ideally suited
for direct driving IGBT with ratings up to 1200V/150A. For
IGBTs with higher ratings, the ACPL-H342/ACPL-K342 can
be used to drive a discrete power stage which drives the
IGBT gate. The ACPL-H342 and ACPL-K342 have the highest
insulation voltage of V_IORM = 891Vpeak and 1140Vpeak
respectively in the IEC/ EN/DIN EN 60747-5-5.
Functional Diagram
ANODE 1
NC 2
CATHODE 3
NC 4
VV_CC_LLA_AM_MP_P
8 VCC
7 VOUT
6 VCLAMP
5 VEE
Note: Design Note: A 1 μF bypass capacitor must be connected between
pins V_CC and V_EE.
Truth Table
• 2.5 A Maximum Peak Output Current
• 2.0A Minimum Peak Output Current
• Built-in Active Miller Clamp
• Rail-to-Rail Output Voltage
• Fast Propagation Delay to minimize Dead Time
• t_PHL < t_PLH to provide “Anti-Cross” Conduction
• LED input threshold current hysteresis
• I_CC = 2.5 mA Maximum Supply Current to allow boot-
strap power supply
• Under Voltage Lock-Out Protection (UVLO) with
Hysteresis
• 40 kV/µs Minimum Common Mode Rejection (CMR) at
V_CM = 1500 V
• Wide Operating V_CC Range: 15 to 30 Volts
• Industrial Temperature Range: -40°C to 105°C
• Safety Approval:
– UL Recognized 3750/5000 V_RMS for 1min.
– CSA
– IEC/EN/DIN EN 60747-5-5 V_IORM = 891/1140 Vpeak
Applications
• IGBT/MOSFET Gate Drive
• AC and Brushless DC Motor Drives
• Renewable Energy Inverters
• Industrial Inverters
• Switching Power Supplies
V_CC – V_EE
V_CC – V_EE
“POSITIVE GOING” “NEGATIVE GOING”
LED (i.e., TURN-ON) (i.e., TURN-OFF)
V_O
V_CLAMP
OFF
0 – 30V
0 – 30V
LOW
LOW
ON
0 – 11V
0 – 9.5V
LOW
LOW
ON
11 – 13.5V
9.5 – 12V
TRANSITION TRANSITION
ON
13.5 – 30V
12 – 30V
HIGH
Hi-Z
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.