T0820_05 Datasheet, PDF (6/12 Pages) ATMEL Corporation – 4-channel Laser Driver with RF Oscillator

7. Electrical Characteristics: Laser Amplifier
V_CC = 5V, T_amb = 25°C, ENABLE = High, unless otherwise specified
No. Parameters
Test Conditions
Pin Symbol Min.
Typ.
Max.
Unit
4 Laser Amplifier
4.1 Best fit current gain
4.2 Best fit current offset
4.3 Output current linearity
Any channel⁽¹⁾
Any channel⁽¹⁾
Any channel⁽¹⁾
14
GAIN
90
105
130 mA/mA
14
IOS
–8
+4
mA
14
ILIN
–3
+3
%
4.4 Input current range
Input is sinking
1, 2, 4,
5
IDAC
0
3
mA
4.5
Output current read
channel
Output is sourcing
14
I_OUTR
150
mA
4.6 Output current channel 2 Output is sourcing
14
I_OUT2
150
mA
4.7 Output current channel 3 Output is sourcing
14
I_OUT3
200
mA
4.8 Output current channel 4 Output is sourcing
14
I_OUT4
200
mA
4.9
Output current read
channel + channel 2
Output is sourcing
14
I_OUTR,2
150
mA
4.10
Output current channel 3 +
channel 4
Output is sourcing
14
I_OUT3,4
200
mA
4.11 Total output current
4.12 IOUT series resistor
4.13 I_IN input impedance
Output is sourcing
I_OUT = 250 mA total
R_OUT to V_CC-Rail
R_IN is to GND
14
14
1, 2, 4,
5
I_OUT
R_OUT
R_IN
300
mA
8
Ω
150
200
250
Ω
4.14 NE threshold
Temperature stabilized 6, 7, 8 VTH
1.68
V
4.15 Output off current 1
ENABLE = Low
IOFF₁
NE2 = NE3 = NE4 =
4.16 Output off current 2
High, I_IR = 0 µA,
I_I2 = I_I3 = I_I4 = 500 µA
14
IOFF₂
4.17 Output off current 3
NE2 = NE3 = NE4 =
Low, I_IR = I_I2 = I_I3 =
I_I4= 0 µA
14
IOFF₃
4.18
I_OUT supply sensitivity,
read mode
I_OUT = 40 mA,
V_CC = 5V ±10%,
read only
14
VSE_R
–4
1
mA
1
mA
5
mA
–1
%/V
4.19
I_OUT supply sensitivity,
write mode
I_OUT = 80 mA, 40 mA
read + 40 mA write,
V_CC = 5V ±10%
14
VSE_W
–4
0.2
%/V
4.20 I_OUT current output noise
I_OUT = 40 mA,
ENOSC = Low
14
INO_O
3
nA/
rt-Hz
4.21
I_OUT temperature
sensitivity, read mode
I_OUT = 40 mA, read only 14
TSE_R
–500
ppm/°C
4.22
I_OUT temperature
sensitivity, write mode
I_OUT = 80 mA, 40 mA
read + 40 mA Write
14
TSE_W
–600
ppm/°C
*) Type means: A =100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note: 1. Linearity of the amplifier is calculated using a best fit method at three operating points of
I_OUT at 20 mA, 40 mA, and 60 mA. I_OUT = (I_IN × GAIN) + I_OS
Type*
A
A
A
C
A
A
A
A
A
A
A
C
A
B
A
A
A
A
A
C
C
C
6 T0820
4506G–DVD–11/05