AT88SC0104CA_14 Datasheet, PDF (59/71 Pages) ATMEL Corporation – Atmel CryptoMemory

12. Absolute Maximum Ratings*
Operating temperature....................−40°C to +85°C
Storage temperature ...................−65°C to + 150°C
Voltage on any pin
with respect to ground ...............− 0.7 to VCC +0.7V
Maximum operating voltage................................ 6V
DC output current ............................................ 5mA
*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at these or any other condition
beyond those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of
time may affect device reliability.
12.1 DC and AC Characteristics
Table 12-1. DC Characteristics
Symbol Parameter
Test Condition
Min
Typ
Max
Units
VCC
ICC
ICC
ICC
ICC
ISB
VIL
VIL
VIL
VIH(3)
VIH(3)
VIH(3)
IIL
IIL
IIL
IIH
IIH
IIH
VOH
VOL
IOH
IOL
Supply Voltage
Supply Current (VCC = 3.3V)
Supply Current (VCC = 3.3V)
Supply Current (VCC = 3.3V)
Supply Current (VCC = 3.3V)
Standby Current (VCC = 3.3V)
SDA/IO Input Low Voltage
CLK Input Low Voltage
RST Input Low Voltage
SDA/IO Input High Voltage
SCL/CLK Input High Voltage
RST Input High Voltage
SDA/IO Input Low Current
SCL/CLK Input Low Current
RST Input Low Current
SDA/IO Input High Current
SCL/CLK Input High Current
RST Input High Voltage
SDA/IO Output High Voltage
SDA/IO Output Low Voltage
SDA/IO Output High Current
SDA/IO Output High Current
Async Read at 3.57MHz
Async Write at 3.57MHz
Synch Read at 1MHz
Synch Write at 1MHz
VIN = VCC or GND
0 < VIL < VCC x 0.15
0 < VIL < VCC x 0.15
0 < VIL < VCC x 0.15
VCC x 0.7 < VIH < VCC
VCC x 0.7 < VIH < VCC
VCC x 0.7 < VIH < VCC
20K Ω external pull-up
IOL = 1mA
VOH
VOL
2.7
0
0
0
VCC x 0.7
VCC x 0.7
VCC x 0.7
VCC x 0.7
0
3.6
V
5
mA
5
mA
5
mA
5
mA
100
µA
VCC x 0.2
V
VCC x 0.2
V
VCC x 0.2
V
5.5
V
5.5
V
5.5
V
15
µA
15
µA
50
µA
20
µA
100
µA
150
µA
VCC
V
VCC x 0.15
V
20
µA
10
µA
Notes: 1. Applicable over recommended operating voltage range from VCC = 2.7V to 3.6V.
2. TAC = -40°C to +85°C (unless otherwise noted).
3. To prevent latch up conditions from occurring during power up of the AT88SCXXXXCA, VCC must be turned on
before applying VIH. For powering down, VIH must be removed before turning VCC off.
AT88SC0104CA/0204CA/0404CA/0808CA [Datasheet]
59
Atmel-8664F-CryptoMem-Low-Density-Full-Specification-Datasheet_022014