ATTINY26_06 Datasheet, PDF (56/185 Pages) ATMEL Corporation – 8-bit Microcontroller with 2K Bytes Flash

• DI/SDA/OC1A/PCINT0 – Port B, Bit 0
DI: Data Input in USI Three-wire mode. USI Three-wire mode does not override normal
port functions., so pin must be configure as an input.
SDA: Serial Data in USI Two-wire mode. Serial data pin is bi-directional and uses open-
collector output. The SDA pin is enabled by setting the pin as an output. The pin is
pulled low when the PORTB0 or USI shiftRegister is zero when DDB0 is set (one). Pull-
up is disabled in USI Two-wire mode.
OC1A: Inverted Timer/Counter1 PWM output A: The PB0 pin can serve as an Inverted
output for the PWM mode if not used in programming or USI. The PB0 pin has to be
configured as an output (DDB0 set (one)) to serve this function.
PCINT0: Pin Change Interrupt 0 pin. Pin change interrupt is enabled on pin when global
interrupt is enabled, pin change interrupt is enabled and the alternate functions do not
mask the interrupt. The masking alternate functions are the inverted output compare
match output OC1A and USI data DI or SDA. Digital input is enabled on pin PB0 also in
SLEEP modes, if the pin change interrupt is enabled and not masked by the alternate
functions. Table 27 and Table 28 relate the alternate functions of Port B to the overriding
signals shown in “Alternate Port Functions” on page 48.
Table 27. Overriding Signals for Alternate Functions in PB7..PB4
Signal
Name
PUOE
PB7/ADC10/RESET/
PCINT1
RSTDSBL⁽¹⁾
PB6/ADC9/INT0/TO/
PCINT1
0
PB5/ADC8/XTAL2/
PCINT1
~⁽⁵⁾PB5IOENABLE⁽³⁾
PB4/ADC7/XTAL1
~PB4IOENABLE⁽³⁾
PUOV
DDOE
1
RSTDSBL⁽¹⁾
0
0
0
0
~PB5IOENABLE⁽³⁾
~PB4IOENABLE⁽³⁾
DDOV 0
0
0
0
PVOE 0
0
0
0
PVOV
DIEOE
0
PCINT1_ENABLE⁽²⁾ | RSTDSBL⁽¹⁾
DIEOV
PCINT1_ENABLE⁽²⁾ •
~⁽⁵⁾RSTDSBL⁽¹⁾
0
~T0_EXT_CLOCK ⁽⁶⁾ •
PCINT1_ENABLE⁽²⁾ |
INT0_ENABLE⁽⁴⁾
1
0
PCINT1_ENABLE⁽²⁾ |
~PB5IOENABLE⁽³⁾
PCINT1_ENABLE⁽²⁾ •
PB5IOENABLE⁽³⁾
0
PCINT_ ENABLE ⁽²⁾ |
~PB4IOENABLE⁽³⁾ |
EXT_CLOCK_ENABLE⁽⁷⁾
PCINT1_ENABLE⁽²⁾•
PB4IOENABLE⁽³⁾ |
EXT_CLOCK_ENABLE
DI
PCINT1
INT0, T0, PCINT1
PCINT1
External Clock, PCINT1
AIO
ADC10, RESET INPUT
ADC9
ADC8, XTAL2
XTAL1
Notes:
1. RSTDISBL Fuse (active low) is described in section “System Control and Reset” on page 33.
2. Note that the PCINT1 Interrupt is only enabled if both the Global Interrupt Flag is enabled, the PCIE1 flag in GIMSK is set
and the alternate function of the pin is disabled as described in “Pin Change Interrupt” on page 64.
3. PB5IOENABLE and PB4IOENABLE are given by the PLLCK and CKSEL Fuses as described in “Clock Sources” on page
26.
4. External low level interrupt is enabled if both the Global Interrupt Flag is enabled and the INT0 flag in GIMSK is set as
described in “External Interrupt” on page 64.
5. Not operator is marked with “~”.
6. The operation of the Timer/Counter0 with external clock disabled is described in “8-bit Timer/Counter0” on page 67.
7. External clock is selected by the PLLCK and CKSEL Fuses as described in “Clock Sources” on page 26.
56 ATtiny26(L)
1477I–AVR–10/06