AD7322 Datasheet, PDF (1/18 Pages) ATMEL Corporation – Software Selectable True Bipolar Input, 2-Channel, 12-Bit Plus Sign ADC

Preliminary Technical Data
Software Selectable True Bipolar Input,
2-Channel, 12-Bit Plus Sign ADC
AD7322*
FEATURES
• 12-Bit Plus Sign SAR ADC
• True Bipolar Analog Inputs
• Software Selectable Input Ranges
± 10V, ± 5V, ± 2.5V, 0 to 10V
• Two Analog Inputs with Channel Sequencer
• Single Ended, True Differential and Pseudo Differential
Capability.
• High Analog Input Impedance
• Low Power:- 6 mW
• Full Power Signal Bandwidth: >13 MHz
• Internal 2.5 V Reference
• High Speed Serial Interface
• Power Down Modes
• 14-Lead TSSOP
• For 8 and 4 channel equivalent devices see AD7328 and
AD7324 respectively.
GENERAL DESCRIPTION
The AD7322 is a 2-Channel, 12-Bit Plus Sign, 1 MSPS
Successive Approximation ADC. The ADC has a high speed
serial interface that can operate at throughput rates up to 1
MSPS.
The AD7322 can handle True Bipolar Analog input signals. The
Bipolar ranges are software selectable by programming the on
board Range Register. Bipolar input ranges include ± 10V, ± 5V,
± 2.5V. The AD7322 can also handle a 0 to 10 V uniploar input
range, which is also software selectable. Each analog input
channel can be independently programmed to one of the input
ranges by setting the appropriate bits in the Range Register.
The Analog Input Channels can be configured as Single-Ended,
Fully Differential or Pseudo Differential. Dedicated Control
Register bits are used to configure the Analog inputs. The
AD7322 contains a Channel Sequencer, allowing automatic
conversions between each analog input channel.
The ADC contains a 2.5V Internal reference. The AD7322 also
allows for external Reference operation. If a 3V external
reference is applied to the REFIN/OUT pin, the ADC can
handle a True Bipolar ± 12 V Analog input range. Minimum
VDD and VSS supplies of ± 12V are required for this ± 12 V input
range.
* Patent Pending
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
The Serial clock frequency, SCLK, applied to the ADC will
determine the maximum throughput rate the ADC can operate
at. The SCLK signal is used as the conversion clock and also to
transfer data to and from the ADC. The Serial interface is
SPI^TM, QSPI^TM, MICROWIRE^TM and DSP compatible.
The AD7322 offers power down modes to reduce the power
consumption of the ADC at lower throughput rates.
PRODUCT HIGHLIGHTS
1. The AD7322 can accept True Bipolar Analog Input signals,
±10V, ±5V, ±2.5V and 0 to 10V unipolar signals.
2. The Two Analog Inputs can be configured as Two Single-
Ended inputs, One True Differential or One Pseudo Differential
Input. The AD7322 has high Impedance Analog Inputs.
3. The AD7322 features a High Speed Serial Interface.
Throughput Rates up to 1 MSPS can be achieved on the
AD7322.
4. Low Power, 12 mW at maximum throughput rate of 1 MSPS.
Rev. PrE
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone]
www.analog.com
Fax: [phone] © 2004 Analog Devices, Inc. All rights reserved.