SP480 Datasheet, PDF (2/4 Pages) Astrodyne Corporation – 480W Single Output with PFC Function

480W Single Output with PFC Function
INPUT SPECIFICATIONS
SP480 series
GENERAL SPECIFICATIONS
Input Voltage Range (Note 5)
Frequency Range
Inrush Current, typ: (cold start)
Input Current

Leakage current
Min Load
Power Factor @ FL

90 ~ 264VAC 120~370 Volts(DC)
47-63 Hz
20Amps/115VAC; 40Amps 230VAC
6.5Amps @ 115VAC
3.5 Amps @ 230VAC
< 2mAmps / 240VAC
See Selection Chart
PF > 0.95 / 230VAC
> 0.98 / 115VAC
OUTPUT SPECIFICATIONS
Voltage and Current (Note3) See Selection Chart
Line Regulation
±0.5%: 3.3;5Volts(DC)

±0.3%: 12;15Volts(DC)

±0.2%: 24;48Volts(DC)
Load Regulation
±1.0%: 3;5Volts(DC)

±0.5%: 12~48Volts(DC)
Voltage Tolerance (Note 2) ±2.0%: 3.3;5Volts(DC)

±1.5%: 12;15Volts(DC)

±1.0%: 24;48Volts(DC)
Ripple/Noise (Note 1)
80mVpk-pk: 3.3;5Volts(DC)

120mVpk-pk: 12Volts(DC)

150mVpk-pk: 15;24Volts(DC)

240mVpk-pk: 48Volts(DC)
Hold Up Time @ FL
18mS /230VAC

18mS /115VAC
Setup, Rise Time @ FL
1000mS, 80mS /230VAC

2500mS, 80mS /115VAC
Over Voltage Protection
See Selection Chart

Shut down o/p volt,re power
Over Current Protection
See Selection Chart

Constant current limiting,auto recover
Over Temperature (Note 3)
80°C TSW1: detect on heatsink of power transistor
90°C TSW2: detect on heatsink of power diode
Shut down o/p voltage, auto recover
DC Volt Adjust
See Selection Chart
Peak Load: 10min (Note 4 ) 10% max
Safety

Insulation Resistance
EMI
Harmonic Current
Remote Control

Efficiency
Isolation


EMS



UL60950-1,
TUV EN60950-1 Approved
≥ 100MΩ / 500Volts(DC)
Compliance to EN55022B (CISPR22B)
Compliance to EN61000-3-2,-3
RC+/RC-: 4~10Volts(DC) Power off
0 ~ 0.8Volts(DC) Power on
See Selection Chart
3000VAC Input - Output
1500VAC Input - Ground
Short Output - Ground
Compliance to
EN61000-4-2,3,4,5,6,8,11
ENV50204,EN61000-6-2(EN50082-2)
light Industry Level, Criteria A
ENVIRONMENTAL SPECIFICATIONS
Oper. Temperature
-20°C to +60°C (See Derate Curve)
Storage Temperature
-40°C to +85°C, 10~95% RH
Relative Humidity
20~90% RH non cond
Temperature Coefficient ±0.03% / °C (0-50°C)
MTBF
120.5KHrs min,MIL-HDBK-217F(25°C)
Vibration
10~500Hz, 2G10min./1cycle, period for

60min. each along X, Y, Z axes
PHYSICAL SPECIFICATIONS
Size
278x127 x 43mm (10.94”x5 ”x1.69”)
Weight
59.97 oz (1700g)
NOTE
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”
twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Tolerance : includes set up tolerance, line regulation and load regula-
tion.
3. TSW1: Detect on heatsink of power transistor.
TSW2: Detect on heatsink of output diode.
4. 33% Duty cycle maximum within every 30 minute. Average output
power should not exceed the rated POWER.
5. Derating may be needed under low input voltages. Please check the
derating curve for more details.
All specifications are typical at nominal input, full load, and 25°C unless other-
wise noted
WWW.ASTRODYNETDI.COM
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458