SP150DRL Datasheet, PDF (2/5 Pages) Astrodyne Corporation – 150W Single Output with PFC Function

150W Single Output with PFC Function
SP150/DRL series
INPUT SPECIFICATIONS
Input Voltage Range (Note3)
Frequency Range
Inrush Current, typ: (cold start)
Input Current

Leakage current
Min Load
Power Factor @ FL

90 ~ 264VAC 120~370 Volts(DC)
47-63 Hz
40Amps / 230VAC
2.5 Amps. @ 115VAC
1.2 Amps. @ 230VAC
< 2mAmps / 240VAC
See Selection Chart
PF> 0.93 / 230VAC
> 0.98 / 115VAC
OUTPUT SPECIFICATIONS
Insulation Resistance
≥ 100MΩ / 500Volts(DC)
EMI
Compliance to EN55022 (CISPR22)

Class B
Harmonic Current
Compliance to EN61000-3-2,-3
Efficiency
See Selection Chart
Isolation

3000VAC Input - Output

1500VAC Input - Ground

500VAC Output - Ground
EMS
Compliance to

EN61000-4-2, 3, 4, 5, 6, 8, 11;

ENV50204,EN55024,

light Industry Level, Criteria A
Voltage and Current
Line Regulation
Load Regulation
Voltage Tolerance (Note 2)

Ripple/Noise (Note 1)
Hold Up Time
Setup, Rise Time
Over Voltage Protection









Over Current Protection

Over Temperature


DC Volt Adjust
See Selection Chart
±0.5%
See Selection Chart
±2.0%: 3.3~15Volts(DC)
±1.0%: 24~48Volts(DC)
See Selection Chart
20mS @ FL
600ms, 30m @ FL
3.63 ~ 4.46Volt(DC): 3.3Volts(DC)
5.5 ~ 6.75Volt(DC): 5Volts(DC)
8.25 ~ 10.13Volt(DC): 7.5Volts(DC)
13.2 ~ 16.2Volt(DC): 12Volts(DC)
14.85 ~ 18.2Volt(DC): 13.5Volts(DC)
16.5 ~ 20.25Volt(DC): 15Volts(DC)
26.4 ~ 32.4Volt(DC): 24Volts(DC)
29.7 ~ 36.45Volt(DC): 27Volts(DC)
52.8 ~ 64.8Volt(DC): 48Volts(DC)
Shut down o/p voltage, re-power
105 ~ 150% rated output power
Constant current limiting,auto-recover
95°C +/-5°C TSW1 : detect on
heatsink of power transistor
after cool down
See Selection Chart
ENVIRONMENTAL SPECIFICATIONS
Oper. Temperature
Storage Temperature
Relative Humidity
Temperature Coefficient
MTBF
Vibration

-10°C to +60°C (See Derate Curve)
-20°C to +85°C, 10~95% RH
20~90% RH non cond
±0.05% / °C (0-50°C)
191.2KHrs min,MIL-HDBK-217F(25°C)
10~500Hz, 2G10min./1cycle, period for
60min. each along X, Y, Z axes
PHYSICAL SPECIFICATIONS
Size
Millimeters
199 x 99 x 50
Inches
7.84” x 3.90 ” x 1.97 ”
Weight
26.81 oz (760g)
NOTE
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”
twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Tolerance : includes set up tolerance, line regulation and load regula-
tion.
3. Derating may be needed under low input voltages. Please check the
derating curve for more details.
GENERAL SPECIFICATIONS
Safety
UL60950-1,

TUV EN60950-1 Approved
All specifications are typical at nominal input, full load, and 25°C unless other-
wise noted
WWW.ASTRODYNETDI.COM
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458