LPS75 Datasheet, PDF (2/4 Pages) Astrodyne Corporation – 75W Single Output Switching Power Supply

75W Single Output Switching Power Supply
LPS75 series
INPUT SPECIFICATIONS
Efficiency, typ.

69% (LPS-75-3.3)
77% (LPS-75-5)
Input Voltage Range
90 ~ 264 VAC; 127~370 Volts(DC)
Frequency Range
47-63 Hz

Inrush Current, typ: (cold start)18Amps@115VAC / 36Amps@230VAC
Input Current, typ.
1.9Amps@115VAC

1.1Amps@230VAC ^Isolation
Leakage current
< 1mAmps /240VAC
Min Load
See Selection Chart
EMS
80% (LPS-75-12)
81% (LPS-75-15)
83% (LPS-75-24)
83%(LPS-75-48)
3000VAC Input - Output
1500VAC Input - Ground
500VAC Output - Ground
Compliance to
OUTPUT SPECIFICATIONS
Voltage and Current
See Selection Chart
Line Regulation
±1.0%
Load Regulation
±3.0%: 3.3~5Volts(DC)

±2.0%: 12~15Volts(DC)



Remote ON/OFF

EN61000-4-2, 3, 4, 5, 6, 8, 11;
ENV50204,EN61000-6-2(EN50082-2)
heavy Industry Level, Criteria A
RC+/RC-: 0~0.8Volts(DC)= power On
4~10Volts(DC)= power Off

Voltage Tolerance (Note2)
Ripple/Noise (Note 1)
Hold Up Time,typ @ FL

Setup, Rise Time @ FL

Over Voltage Protection

±1.0%: 24~48Volts(DC)
See Selection Chart ^{ENVIRONMENTAL SPECIFICATIONS}
See Selection Chart ^{Oper. Temperature}
-20°C to +70°C (See Derate Curve)
60mS/230VAC ^{Storage Temperature}
-20°C to +85°C, 10~95% RH
12mS/115VAC ^{Relative Humidity}
20~90% RH non cond
100ms, 35m/230VAC ^{Temperature Coefficient}
±0.04% / °C (0-50°C)
100mS, 35mS/115VAC ^MTBF
355KHrs min,MIL-HDBK-217F(25°C)
3.8 ~ 4.45Volt(DC): 3.3Volts(DC) ^Vibration
10~500Hz, 2G10min./1cycle, period for
5.75 ~ 6.75Volt(DC): 5Volts(DC)
60min. each along X, Y, Z axes


13.8 ~ 16.2Volt(DC): 12Volts(DC)
17.25 ~ 20.25Volt(DC): 15Volts(DC) ^{PHYSICAL SPECIFICATIONS}

27.6~ 32.4Volt(DC): 24Volts(DC)

57.6~ 67.2Volt(DC): 48Volts(DC) ^Size

Hiccup mode, auto recover
Millimeters
222 x 55 x 30
Over Current Protection 115 ~ 150% rated output power
Inches
8.74” x 2.17 ” x 1.18 ”

Hiccup mode, auto recover ^Weight
10.58 oz (300g)
DC Volt Adjust
See Selection Chart
Peak Load, 10S(Note 3) See Selection Chart NOTE
GENERAL SPECIFICATIONS
Safety

Insulation Resistance
EMI
Harmonic Current
UL60950-1,
TUV EN60950-1 Approved
≥ 100MΩ / 500Volts(DC)
Compliance to EN55022B (CISPR22B)
Compliance to EN61000-3-2,-3
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”
twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Tolerance : includes set up tolerance, line regulation and load regula-
tion.
3. 33.3% Duty cycle maximum within every 30 seconds. Average output
power should not exceed the rated power.
All specifications are typical at nominal input, full load, and 25°C unless other-
wise noted
WWW.ASTRODYNETDI.COM
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458