CNS653-ME Datasheet, PDF (3/8 Pages) Artesyn Technologies – 650 Watt AC-DC Power Supplies

CNS650-M Series Data Sheet
Ordering Information
Model Number
Output
Voltage
Vout Adjust
Range
(-0% /+15%)
Minimum
Load
Max. Continuous
Load
(Free Air)
Max. Peak
Load
(Free Air)¹
Max. Continuous Max. Peak
Load
Load
(Forced Air)² (Forced Air)²
CNS653-ME⁵
12 V
12 - 13.8 V
0A
NA
NA
54.2 A
62.5 A
CNS653-MF⁵
12 V
12 - 13.8 V
0A
30.0 A
54.2 A
54.2 A
62.5 A
CNS653-MU
12 V
12 - 13.8 V
0A
33.3 A
54.2 A
54.2 A
62.5 A
CNS655-MU
24 V
24 - 27.6 V
0A
16.7 A
27.1 A
27.1 A
31.3 A
CNS658-MU
48 V
48 - 55.2 V
0A
8.3 A
13.5 A
13.5 A
15.6 A
1 _{Peak load current not to exceed 10 seconds, Ta = 50 °C.}
2 _{Requires at least 400 LFM of airflow.}
3 _{At 25 °C including factory setpoint, line voltage and load current variations.}
4 _{Peak-to-peak ripple measured at the output terminal with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with 0.1 µF capacitor across the output.}
5 _{Optional Suffix “-ME” (end-fan) and “-MF: (open-frame) available on the 12 V output.}
Regulation³ Ripple (p-p)⁴
±2%
±2%
±2%
±2%
±2%
120 mV
120 mV
120 mV
240 mV
480 mV
Input Connections (-MU and -MF Suffix)
Pin Function Power Supply Side
System Side
TB1
PE
TB2
L2/Neutral
Dinkle EHK762V-03P
Max Torque: 4kgf-cm
TB3 L1/Line
Input Connections (-ME Suffix)
Pin Function Power Supply Side
Recommended Wire
Size: AWG #22 to #14
System Side
IEC
Inlet
Input AC
IEC 60320 C14 (Male)
IEC Cord C13 (Female)
Output Connections
Pin Function Power Supply Side
BAR1
BAR2
BAR3
BAR4
-Vout
-Vout
+Vout
+Vout
Output Terminal Screw:
M4X8 (4X)
Max Torque: 10kgf-cm
System Side
Molex 19099-0032 or
19141-0063 for AWG #16
to #14
Molex 19099-0048 or
19141-0083 for AWG #12
to #10
Other Output and Control Connections (Connector J304)
Pin Designation
Description
1
5VSB
2
5VSB
+5 V Standby Output
+5 V Standby Output
3
5VSB_GND
4
SCL
5
A0
+5 V Standby Output Return/Ground
Serial Clock Signal (I2C)
EEPROM Address
6
SDA
7
I_SHARE
Serial Data Signal (I2C)
Active current share pin
8
SYS_GND
9
12VFAN
10
REMOTE INHIBIT
Return Ground for signals and I2C
12 V Fan Output
Output Inhibit Pin (Main Output)
11
FAN_RTN
12
VIN_GOOD
12 V Fan Output Return/Ground
Input Line OK Signal
13
FAN_PWM1
14
PWOK
FAN PWM
Output Power OK Signal
15
FAN_TACH1
Fan1 Tacho Signal
16
FAN_OVERRIDE
17
FAN_FAIL
External Fan Sensor for Override
Fain Fail Signal
18
FAN_FAULT_EN
19
REMOTE_SENSE+
FAN Fault Enable Due to low RPM
Positive Remote Sense
20
REMOTE_SENSE-
Remote Sense Return
J304 20-Pin Connector (PSU Side):
Landwin: 2052P20008T or
CviLux: CI0120P1HD0-LF
Recommended Mating Connectors:
CviLux: CI0120SD000 (housing)
CI01TD21PE0 (contact pins)
Landwin: 2050S2000 (housing)
2053T021V (contact pins)
JST: PHDR-20VS (housing)
SPHD-001T-P0.5 (contact pins)
See ACCESSORIES Section