NAL25 Datasheet, PDF (1/3 Pages) Artesyn Technologies – 25W AC/DC Universal Input Switch Mode Power Supplies

NAL25 Series
Single and triple output
LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 25W AC/DC Universal Input Switch Mode Power Supplies 1
• 5.0 x 3.0 x 1.2 inch package (1U applications)
• Ideal for high volume designs
• Industry standard package
• Overvoltage and short circuit protection
• 25W with free air convection cooling
• EN55022, EN55011 conducted emissions level A
• UL, VDE, CSA and BABT safety approvals
• Available RoHS compliant
The NAL25 series are 25W universal input AC/DC power supplies on a 5 x 3 inch
card with a maximum component height of 1.2 inches for use in 1U applications.
This series is available in an industry standard 5 x 3 inch footprint at low cost
making the series ideal for new and existing high volume communication and
industrial applications. The NAL25 series meets level A conducted emissions. The
NAL25 series provide 25W of output power with free air convection cooling with a
peak of 30W for a maximum of 60 seconds. The NAL25 series are designed for use
in high volume low power data networking, computer and telecom applications such
as hubs, POS terminals, modems and small PABX's. This list is not exclusive as the
generic feature set of both series with industry standard output configurations
provide a solution for most high volume applications including many industrial
applications.
All specifications are typical at nominal input, full load at 25°C unless otherwise stated
2 YEAR WARRANTY
SPECIFICATIONS
OUTPUT SPECIFICATIONS
Line regulation
Main output
Auxiliary outputs
Total regulation
Main output
Auxiliary outputs
Overshoot/undershoot At turn-on
Transient response
+5.1V
(1A to 2A step)
Temperature coefficient
Overvoltage protection +5.1V output
Output power limit
Primary power
limited
Short circuit protection
Minimum output current
INPUT SPECIFICATIONS
Input voltage range
Input frequency range
Input surge current
Safety ground
leakage current
110VAC
230VAC
110VAC, 60Hz
230VAC, 50Hz
±0.5%
±1.0%
±3.0%
±5.0%
<10%
±150mV max. dev.,
500µs recovery
±0.02%/°C
5.5V to 7.0V
80W Pin limit, max.
30W Pout limit, min.
Continuous
See derating curve
90 to 264VAC
120 to 370VDC
47Hz to 440Hz
18A max.
38A max.
0.2mA
0.4mA
EMC CHARACTERISTICS
Conducted emissions
Radiated emissions
ESD air
ESD contact
Surge
Fast transients
Radiated immunity
Conducted immunity
EN55022, FCC part 15
EN55022, FCC part 15
EN61000-4-2, level 3
EN61000-4-2, level 4
EN61000-4-5, level 3
EN61000-4-4, level 3
EN61000-4-3, level 3
EN61000-4-6, level 3
level A
level A
Perf. criteria 2
Perf. criteria 2
Perf. criteria 2
Perf. criteria 2
Perf. criteria 2
Perf. criteria 1
GENERAL SPECIFICATIONS
Hold-up time
110VAC
230VAC
10ms @ 25W
60ms @ 25W
Efficiency
70%
Isolation voltage
Input/output
Input/chassis
3000VAC
1500VAC
Switching frequency
Variable
Approvals and
standards
(See Note 8)
VDE0805, EN60950, IEC950
BABT, IEC1010, UL1950
CSA C22.2 No. 950
Weight
200g (7.06oz)
MTBF
MIL-HDBK-217F 150,000 hours min.
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
(See Notes 6, 7)
Operating ambient,
(See derating curve)
0°C to +70°C
Non-operating
-40°C to +85°C
50°C to 70°C ambient,
convection cooled
Derate to
50% load
0C to 50C, ambient,
convection cooled
25W
Peak (0°C to +50°C, 60s)
30W
Relative humidity
Non-condensing
5% to 95% RH
Altitude
Operating
Non-operating
10,000 feet max.
30,000 feet max.
Vibration (See Note 5) 5Hz to 500Hz
2.4G rms
File Name: nal25.pdf Rev: 30 Mar 2006