N1000 Datasheet, PDF (1/4 Pages) Artesyn Technologies – Single, dual, triple and quad output 1000 and 1200 Watt AC/DC high wattage power supplies with PFC

N1000 and N1200 SERIES
Single, dual, triple and quad output
[ 2 YEAR WARRANTY ]
• Active harmonic correction to EN61000-3-2
• 90VAC to 264VAC universal input
• Flexible output voltage configuration
• Two output power ratings
• Forced current sharing, all outputs
• DC OK (including LED)
• UL, CSA and TÜV safety approvals
• Industry standard 5 x 8 x 11 inch footprint
The N1000 and N1200 series are a range of systems-orientated, one to four
output power supplies which provide 1000W or 1200W of continuous power at
line voltages from 90VAC to 264VAC. Both series are harmonically corrected and
carry world wide safety approvals. Fully enclosed, fan cooled and in the industry
standard 5 x 8 x 11 inch form, the N series is an ideal choice when the economy
and predictable performance of a centralized system power supply are desired. A
unique dual converter architecture isolates the 5VDC logic output and the
peripheral voltages. Maximum flexibility is provided as power budgets shift and
change during the design cycle or as system upgrades are implemented. This
overcomes a major shortfall of many system power supplies which use a single
converter. To meet redundancy requirements, each output rail is isolated,
individually regulated and features forced current share. System interface signals
include AC and DC Good, current monitor (V1), overvoltage, OCP, over-
temperature protection, remote enable, margin check and inhibit as standard. By
combining robust performance and broad range, the N Series sets the standard
for centralized system power supplies.
SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated
OUTPUT SPECIFICATIONS ⁽²⁾
Voltage adjustability Accessible at front panel
±10%
Remote sense
Open/reverse sense lead protection
Compensates for voltage drop of up to
0.5V to the load
Regulation, line or load All outputs, NL-FL
at nominal line or all
line variations at FL
±0.2%;
10mV min.
Cross regulation
0.2% max. or 10mV between outputs
Overshoot/undershoot
None at turn on/off
Transient response
Main output
25% step load
change at 1A/µs
≤2.0% max. dev.,
≤200µs recovery
to 1.0%
Temperature coefficient
±0.02%/°C
Ripple and noise
0Hz to 20MHz 50mV pk-pk or 1%
Overvoltage protection Reset by cycling AC
115 to 130%
of nominal
Overload protection
105-115% full load
Short circuit protection All outputs
Auto recovery
Thermal protection
Auto shutdown, AC reset
Current sharing
±5.0%
50% to 100% load
Current monitor (V1) 5VDC at full load
±0.5V
INPUT SPECIFICATIONS
Input voltage range
90 to 264VAC
Input frequency range
47Hz to 63Hz
Input surge current
Meets IEEE std. 587.1980;
3KV ring wave
Input current
120VAC, 1000W
12A
Power factor
115/230VAC, 1kW load 0.995 min.
Power up time
Full load
1.0s max.
PAGE 1
EMC CHARACTERISTICS
Radiated emissions
Conducted emissions
Harmonic distortion
Electrostatic discharge
RF field susceptibility
Electrical fast
transients/bursts
Surge susceptibility
EN55022/11, FCC part 15
EN55022/11, FCC part 15
EN61000-3-2
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
Level A
Level A
Conforms
Level 3
Level 3
Level 3
Level 3
GENERAL SPECIFICATIONS
Hold-up time
90VAC, 1KW load
24ms min.
Efficiency
230VAC, full load
73%
Isolation voltage
Input/output
Input/chassis
Output/output
3000VAC
1500VAC
500VAC
Switching frequency
100kHz
Approvals and
standards
EN60950, UL1950,
CSA C22.2 No. 950
Weight
6.9kg (15Ibs)
Size
5 x 8 x 11 inches
127 x 203.2 x 279.4 mm
MTBF
per MIL-HDBK-217E 100,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance Operating ambient
Non-operating
0°C to +50°C
-15°C to +85°C
Cooling
60CFM Internal DC ball bearing fan
Relative humidity
Non-condensing
0% to 95% RH
Altitude
Operating
Non-operating
6,000 feet max.
55,000 feet max.
Vibration
5Hz to 500Hz
2.4G rms peak