M3000 Datasheet, PDF (1/4 Pages) Artesyn Technologies – Single output 3000 and 4000 Watt AC/DC high current power supplies with PFC

[ 2 YEAR WARRANTY ]
M3000 and M4000 SERIES
Single output
• Load currents up to 800A
• 3 phase or single phase input
• Shutdown on phase loss
• 3 phase power factor correction
• Single wire current share to 5%
• Ideal for N+1 applications
• Current monitor output included
• UL, CSA and TÜV safety approvals
The M series is a range of single output, high current power supplies ideally suited to a
broad range of applications. Robust performance and field proven reliability are
hallmarks of this series. Field reliability in excess of 100,000 hours has been
documented. The M series will provide stable power for any large electronic system
including telecommunication, data processing and industrial. Typical applications
include broadcast systems, ATM systems and RISC processors and systems.
Semiconductor test equipment, semiconductor and wafer processing equipment and
functional board level testers are other possible applications. Industrial uses include
applications such as laser cutting, water purification, battery charging, machine control,
large scale data logging and optical inspection equipment. Current sharing, built-in
current monitoring, voltage margining and remote adjustment capability are standard
features. Other system interface features include AC and DC good, OVP, OCP, over
temperature protection and remote enable. Worldwide safety certifications are included.
SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated
OUTPUT SPECIFICATIONS
Voltage adjustability Accessible at front panel
±10%
Remote sense
Open/reverse sense lead protection
Compensates for voltage drop
of up to 0.5V to the load
Regulation, line or load All outputs, NL to FL
at nominal line or all
line variations at FL
±0.2%; 10mV
Overshoot/undershoot
None at turn on/off
Transient response
Main output
25% step load
change at 1A/µs
≤5.0% max. dev.,
≤200µs recovery
to 1.0%
Temperature coefficient
0.02%/°C
Ripple and noise
0Hz to 20MHz 100mV pk-pk or 1.0%
Overvoltage protection Reset by cycling AC 115% to 130%
of nominal
Overload protection
105% to 115% full load
Short circuit protection 90% of rated load
Auto recovery
Thermal protection
Auto shutdown, AC reset
Current sharing
±5.0%
50% to 100% load
Current monitor (V1) 5VDC at full load
±0.5V
INPUT SPECIFICATIONS
Input voltage range
3 phase
1 phase (optional)
180 to 264VAC
180 to 264VAC
Input frequency range
47Hz to 63Hz
Input surge current
Meets IEEE std. 587.1980;
3KV ring wave
Input current
208VAC, 3 phase
12A
208VAC, 1 phase
27A
Power factor
3 phase
0.94
1 phase
0.65
Power up time
PAGE 1
Full load
1.0s max.
EMC CHARACTERISTICS
Radiated emissions
Conducted emissions
Electrostatic discharge
RF field susceptibility
Electrical fast
transients/bursts
Surge susceptibility
EN55022/11, FCC part 15
EN55022/11, FCC part 15
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
Level A
Level A
Level 3
Level 3
Level 3
Level 3
GENERAL SPECIFICATIONS
Hold-up time
230VAC, 3KW load
25ms min.
Efficiency
208VAC, 3 phase
83%
Isolation voltage
Input/output
Input/chassis
Output/output
3000VAC
1500VAC
500VAC
Switching frequency
100kHz
Approvals and
standards
TÜV EN60950, UL1950,
CSA C22.2 No. 950
Weight
13kg (29Ibs)
Size
5 x 8 x 13.5 inches
127 x 203.2 x 342.9 mm
MTBF
>100,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance Operating ambient
Non-operating
0°C to +50°C
-15°C to +85°C
Cooling
50CFM
Internal DC
ball bearing fans
Relative humidity
Non-condensing
0% to 95% RH
Altitude
Operating
Non-operating
6,000 feet max.
55,000 feet max.
Vibration
5Hz to 500Hz
2.4G rms peak