DPF1500 Datasheet, PDF (1/2 Pages) Artesyn Technologies – Single output 1500 Watt AC/DC PFC front-end for distributed power architectures

[ 2 YEAR WARRANTY ]
DPF1500 SERIES
Single output
• Efficiency >90%
• 1500W front end
• EN61000-3-2 compliant
• 12.6 x 6.5 x 4.9 inch size
• Hot pluggable
• N+1 redundancy
• Full set of status signals
• EN55022, EN55011 conducted emissions level A
• UL, TÜV and CSA safety approvals
The DPF1500 is a 1500W universal input AC/DC front end power supply in a fully
enclosed hot pluggable case with built-in fan, handle, IEC input connector, on/off
switch and DIN output signal connector. Providing a single 57.8V output at full load
with a full set of status signals. The DPF1500 is designed for use as a front end in
medium power communication applications adopting distributed power architecture.
The DPF1500 provides 1500W of output power and is fully compliant with EN61000-
3-2. Standard features include current sharing and full protection against overvoltage,
overload and short circuit. Remote or local system monitoring is possible via a full set
of status signals that include fan fail, DC good, power fail, remote inhibit and current
monitoring. The DPF1500, with full international safety approval and the CE mark,
meets conducted emissions EN55022 level A. The DPF1500 can be used in
conjunction with our complete range of 3 to 200W DC/DC converters to fully configure
a distributed power system.
SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated
OUTPUT SPECIFICATIONS
Voltage set point
-57.8V ±0.1%
Total regulation
Main output
FL to NL
±5.0%
Rise time
At turn-on
1.0s, max.
Transient response
Main output
50% to 100%
step at 1A/µs
12% max. dev.,
1ms recovery
to 1.0%
Ripple and noise
Main output
0Hz to 20MHz
1.0V pk-pk
Overvoltage protection latching
60V to 71V
Output power limit
1550W
Short circuit protection Non-latching Auto-recovery, 5A rms
max short circuit current
Current sharing
2V droop from 20%
to 100% rated load
Capacitive load
24µF max.
INPUT SPECIFICATIONS
Input voltage range
176 to 264VAC
Input frequency range
47Hz to 63Hz
Input surge current
220VAC, cold start
40A max.
Input surge
300VAC
20ms
Safety ground
leakage current
230VAC, 50Hz
0.4mA
Input current
176VAC, 1500W
13A rms max.
Input fuse
Non-replaceable
15A
Power factor
220VAC
0.96 min.
PAGE 1
EMC CHARACTERISTICS
Radiated noise
EN55022/11, FCC part 15
Conducted noise
EN55022/11, FCC part 15
Harmonic current emm. EN61000-3-2
Electrical fast
transients/bursts
EN61000-4-4
Surge susceptibility EN61000-4-5
Level A
Level A
Compliant
Level 3
Level 3
GENERAL SPECIFICATIONS
Hold-up time
240VAC, 60Hz FL
10ms @ 1500W
Efficiency
90% typ.
Isolation voltage
Input/output
Input/chassis
3000VAC
1500VAC
Switching frequency
50kHz
Approvals and
standards
EN60950, UL1950,
CSA C22.2 No. 950
Weight
6.9kg (15Ibs)
MTBF
500,000 hours
demonstrated
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Operating ambient, FL 0°C to +50°C
Non-operating
-40°C to +85°C
50°C to 70°C ambient,
convection cooled
Derate to
50% load
Cooling
Built-in fan
Relative humidity
Non-condensing
5% to 85% RH
Altitude
Operating
Non-operating
10,000 feet max.
40,000 feet max.
Vibration
5Hz to 500Hz
2.4G rms peak
International Safety Standard Approvals
TÜV ^{VDE0805/EN60950/IEC950}
UL1950 File No. E136005
CSA C22.2 No. 950 File No. LR41062C