CL25 Datasheet, PDF (1/2 Pages) Artesyn Technologies – Single, dual and triple outputs

[ 2 YEAR WARRANTY ]
CL25 SERIES
Single, dual and triple outputs
For new design -ins refer to the SCL25 series instead
• 90VAC to 264VAC Universal Input
• Short Circuit Protected
• VDE, UL, CSA and BABT Approved
• VDE0871 Level B Conducted Noise
• 25W Continuous, 35W Peak Output Power
• Stand alone "listed" equipment
The CL25 Series of 25W (35W peak) external switching power supplies enables
the system specifier to optimise the design for several reasons. Firstly, because
the power supply offers pre-approved SELV outputs, the submission of the
apparatus for safety approval is simplified. Secondly, the task of integrating the
power supply into the mechanical design is eliminated, presenting further
savings by ensuring a shorter and simpler design cycle. These advantages are
complemented by Universal Input, IEC950, UL, CSA and BABT approvals, to
complete a worldwide packaged power solution suitable for a wide variety of
low power, desktop applications.
SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated
OUTPUT SPECIFICATIONS
Line regulation
LL to HL, FL
Single outputs
Multi's: +5.1V output
Multi's: aux. outputs
±0.5%
±0.5%
±1.0%
Overshoot/undershoot At turn-on
10%
Transient response
+5.1V
(40% to 60%
full load step)
±250mV max. dev.
1ms recovery
to 1%
Temperature coefficient All outputs
±0.025%/°C
Overvoltage protection +5V output only
6.25V ±0.75V
Output power limit
Primary power limited 45W Pin max.
Short circuit protection
Continuous
with auto restart
Minimum output current
0A
INPUT SPECIFICATIONS
Input voltage range
90 to 264VAC
120 to 370VDC
Input frequency range
47 to 440Hz
Input surge current
110VAC
230VAC
12A max.
24A max.
Safety ground
leakage current
110VAC, 60Hz
230VAC, 50Hz
1mA max.
2mA max.
ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS
Radiated noise
EN55022, EN55011, FCC
Conducted noise
EN55022, EN55011, FCC
Electrostatic discharge EN61000-4-2
Electrostat. air discharge IEC801-2
RF field susceptibility IEC801-3
Electrical fast
EN61000-4-4
transients/bursts
Surge susceptibility EN61000-4-5
Level A
Level B
Level 4
Level 3
Level 3
Level 3
Level 3
PAGE 1
GENERAL SPECIFICATIONS
Hold-up time
110VAC
230VAC
10ms
60ms
Efficiency
110VAC and 230VAC
70% typical
Isolation voltage
Input/output
Input/chassis
3000VAC
1500VAC
Switching frequency Variable
45kHz to 85kHz
Approvals and
standards
Safety
VDE0805, EN60950
BABT, IEC950, UL1950
CSA C22.2 No. 950
Case material
ABS plastic
Material flammability
UL94-5V
Weight
500g (17.65oz)
MTBF
MIL-HDBK-217E
150,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Operating
0°C to +40°C
Non-operating
–40°C to +85°C
0°C to +40°C ambient,
convection cooled
25W
Peak (0°C to 40°C, max. 60s),
See Note 1
35W
Relative humidity
Non-condensing
5% to 95% RH
Altitude
Operating
Non-operating
10,000 feet max.
30,000 feet max.
Vibration
5Hz to 500Hz
2.4G rms (approx.)
International Safety Standard Approvals
VDE0805/EN60950/IEC950 File No. 10401-3336-1071
geprüfte _{Licence No. 90353, 79517 and 1071}
Sicherhelt
UL1950 File No. E136005
CSA C22.2 No. 950 File No. LR41062C/LR50913/LR101320
Certificate No. 606008