TM3110PM Datasheet, PDF (1/1 Pages) API Technologies Corp – RF AMPLIFIER MODEL

RF AMPLIFIER
MODEL TM3110PM
Available as: TM3110PM, 4 Pin TO-8 (T4)
TN3110PM, 4 Pin Surface Mount (SM3)
BX3110PM, Connectorized Housing (H1)
Features
„ Superior Phase Noise Performance
„ High Output Power: +30 dBm Typical
„ Operating Temp. -55 ºC to +85 ºC
„ Environmental Screening Available
Specifications
CHARACTERISTIC
Frequency (MHz)
Gain (dB)
Power @ 1 dB
Comp. (dBm)
TYPICAL
Ta= 25 ºC
10 - 200 MHz
15.5
+30
MIN/MAX
Ta = -55 ºC to +85 ºC
10 - 200 MHz
15 Min.
+29 Min.
Typical Intermodulation Performance at 25 ºC
Second Order Harmonic Intercept Point ...... +66 dBm (Typ.)
Second Order Two Tone Intercept Point ....... +63 dBm (Typ.)
Third Order Two Tone Intercept Point ........... +45 dBm (Typ.)
Absolute Maximum (No Damage) Ratings
Ambient Operating Temperature ................ -55ºC to +100 ºC
Storage Temperature ................................. -62ºC to +125 ºC
Case Temperature .................................................. +125 ºC
DC Voltage .......................................................... +17 Volts
Continuous RF Input Power .................................. +15 dBm
Short Term RF Input Power ........... 100 mW (1 Minute Max.)
Maximum Peak Power .................... 0.2 Watt (3 µsec Max.)
Guaranteed @ 25 ºC (160 MHz) Phase Noise Performance (dBc/Hz)*
Reverse Isolation (dB)
-17
-16 Max.
VSWR
In
1.8:1
Out
1.8:1
2.0:1 Max.
2.0:1 Max.
Noise Figure (dB)
3.5
4.5 Max.
Power Vdc
+15
mA
240
+15
250 Max.
Note: Care should always be taken to effectively ground the case of each unit.
Frequency
Typical
Guarantee
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
-160
-155
-170
-165
-175
-170
-180
-175
-180
-175
*Note: Phase Noise Performance typically tested at midband.
Bandedge performance may vary.
Typical Performance Data
Gain (dB)
18
Reverse Isolation (dB)
0
-13 0
Phase Noise (dBc/Hz)
17
-10
-1 40
16
-20
15
-30
-1 50
14
Start 10
+32
MHz
1
dB
Comp.
(dBm)^Stop
200 MH z
-4 0 _{St art}
6
10 MHz_Noise
Figure
(dB) ^Stop
2 00 MHz
-1 60
-1 70
+31
5
+30
4
-1 80
+29
3
-19 0
100
1k
10 k
10 0k
1M
+28
Sta rt 10 MH z
2. 0
Input VSWR
2
Stop 200 MHz ^{Start 10 MHz}
2.0
Output VSWR ^{Stop 200 MHz}
Typical
Residual Phase Noise Test Conditions:
1.75
1.75
„ Carrier Frequency: 160 MHz
„ Power Output +29.0 dBm
„ Temperature: 25 ^oC
1.5
Sta rt 10 MH z
1.5
Stop 20 0 MHz Start 1 0 MHz
„ Agilent ES5500 System
Stop 2 00 MHz
Legend
+25 ºC
+85 ºC - - - - - - -55 ºC
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH [phone] · Fax [phone]
Rev.
4/26/10
www.SpectrumMicrowave.com Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH [phone] · Fax [phone]