CZ8045 Datasheet, PDF (1/1 Pages) API Technologies Corp – RF AMPLIFIER

RF AMPLIFIER
MODEL CZ8045
Available as: CZ8045, 3 Pin TO-39 (T10)
Features
n Low Noise Figure: 4 dB Typical
n Operating Temp. -55 ºC to +125 ºC
n Environmental Screening Available
Typical Intermodulation Performance at 25 º C
Second Order Harmonic Intercept Point ...... +15 dBm (Typ.)
Second Order Two Tone Intercept Point ....... + 8 dBm (Typ.)
Third Order Two Tone Intercept Point ........... +10 dBm (Typ.)
Specifications
CHARACTERISTIC
Frequency
Gain (dB)
Power @ 1 dB
Comp. (dBm)
Reverse
Isolation (dB)
TYPICAL
Ta= 25 ºC
300 kHz - 400 MHz
15 dB
-0.2 dBm
-19 dB
MIN/MAX
Ta = -55 ºC to +125ºC
400 kHz - 400 MHz
13.0 dB Min.
-5.0 dBm Min.
-18 dB Max.
Absolute Maximum (No Damage) Ratings
Ambient Operating Temperature .............. -55ºC to + 125 ºC
Storage Temperature ............................... -62ºC to + 150 ºC
Case Temperature ................................................. + 125 ºC
DC Voltage ........................................................... + 6 Volts
DC Current .............................................................. 25 mA
Continuous RF Input Power ................................... + 6 dBm
Short Term RF Input Power ...... 50 Milliwatts (1 Minute Max.)
Maximum Peak Power ................... 0.5 Watt ( 3 µsec Max.)
VSWR
In
1.5:1
Out
2.0:1
2.5:1 Max.
2.5:1 Max.
Noise Figure (dB)
4.0 dB
5.5 dB Max.
Power
Vdc
mA
+3 volts
8 mA
+3 volts
15 mA Max.
Note: Care should always be taken to effectively ground the case of each unit.
Revision 3/18/2013
Typical Performance Data
Gain (dB)
17
Reverse Isolation (dB)
0
6
Noise Figure (dB)
16
- 10
5
15
- 20
4
14
- 30
3
13 _{Start 100 kHz}
- 40
Stop 400 MHz
Start 100 kHz
Stop 400 MHz
2
Start 100 kHz
Stop 400 MHz
1 dB Comp. (dBm)
+2
0
-2
-4
-6
Start 100 kHz
Stop 400 MHz
2.0
1.5
1.0
Start 100 kHz
Input VSWR
3.0
Output VSWR
2.0
Stop 400 MHz
1.0
Start 100 kHz
Stop 400 MHz
Legend
+25 ºC
+125 ºC - - - - - - -55 ºC
All CZ8045 Amplifier is designed for applications in 50 ohm
systems. Three external capacitors and a decoupling impedance are
required. The decoupling impedance must be large in comparison to
the 50 ohm load to minimize gain reduction. Datasheet curves are
based on the noted decoupling impedance. The external capacitors
determine the low frequency response of the amplifier.
Application Information
Schematic Diagram
+Vcc
Internal
Capacitor
Provided
CZ Series Amp
Decoupling
Impedance
1 kOhm
50 Ohm Input
+3 volts
50 Ohm Output
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH [phone] · Fax [phone]
www.SpectrumMicrowave.com ^{Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pwnnsylvania 19154 · PH [phone] · Fax [phone]}