SA50 Datasheet, PDF (2/4 Pages) Pan Jit International Inc. – GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR(VOLTAGE - 5.0 TO 170 Volts 500 Watt Peak Pulse Power)

ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
SA50
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
SUPPLY VOLTAGE, +V_S
OUTPUT CURRENT, peak
LOGIC SUPPLY VOLTAGE, Vcc
POWER DISSIPATION, internal
TEMPERATURE, pin solder - 10s
TEMPERATURE, junction³
TEMPERATURE, storage
OPERATING TEMPERATURE RANGE, case
INPUT VOLTAGE
PARAMETER
TEST CONDITIONS²
MIN
TYP
INPUT
ANALOG INPUT VOLTAGES
Vcc = 12V
MOTOR A, B = 50% Duty Cycle
6
MOTOR A = 100% Duty Cycle High
8
MOTOR B = 100% Duty Cycle High
4
OUTPUT
Vds (ON) VOLTAGE, each MOSFET
TOTAL Ron, both MOSFETs
EFFICIENCY, 5A OUTPUT
SWITCHING FREQUENCY
CURRENT, continuous
CURRENT, peak
SWITCHING CHARACTERISTICS⁴
RISE TIME
FALL TIME
DEAD TIME
Ids = 5A
+V_S = 80V
t = 100 msec
+V_S = 28V, Vcc = 12V, Ic =2A
1.25
0.5
95
40
45
5
7
36
170
100
POWER SUPPLY
+V_S VOLTAGE⁵
Vcc VOLTAGE
Vcc CURRENT
+V_S Current = Load Current
Vcc = 12Vdc
9.5
12
15
THERMAL³
RESISTANCE, junction to case
Full temp range, for each transistor
2.0
RESISTANCE, junction to air
Full temperature range
30
TEMPERATURE RANGE, case
–25
80V⁵
7A
16V
120W¹
300°C
150°C
–65 to +150°C
–65 to +125°C
+1 to Vcc – 1.5 Vdc
MAX
UNITS
Vdc
Vdc
Vdc
1.8
Vdc
Ω
%
50
Khz
A
A
54
nS
250
nS
nS
80
Vdc
15
Vdc
20
mA
°C/W
°C/W
+85
°C
NOTES: 1. Each of the two active output transistors can dissipate 60W.
2. Unless otherwise noted: T_C = 25°C, Vcc = 12Vdc.
3. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation to
achieve high MTTF. For guidance, refer to the heatsink data sheet.
4. Guaranteed but not tested.
5. Derate to 70V below T_C = +25°C.
CAUTION
The SA50 is constructed from MOSFET transistors. ESD handling procedures must be observed.
The internal substrate contains beryllia (BeO). Do not break the seal. If accidentally broken, do not crush, machine, or
subject to temperatures in excess of 850°C to avoid generating toxic fumes.
WARNING—AMPLIFIER PROTECTION
The SA50 contains an internal logic chip that turns on and
turns off output MOSFET drivers at a certain sequence. Noises
or oscillation caused by external wiring inductance, lack of
proper power supply bypass capacitors, ground, supply and
local internal loops, may be fed back to this logic chip and
cause it to turn on one or more MOSFET drivers at the wrong
time, thus destroying the SA50. A well laid out PC board with
low impedance copper ground plane is necessary for the
SA50 to function properly. The Apex EK-SA50 evaluation
board is recommended for fast and easy breadboarding of
circuits using the SA50.
APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: [phone]
2