|
AAT3783 Datasheet, PDF (1/20 Pages) Advanced Analogic Technologies – 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection | |||
|
PRODUCT DATASHEET
AAT3783
BatteryManagerTM 1-A Linear Li-Ion/Polymer Battery Charger with 28V Over-Voltage Protection
General Description
The AAT3783 BatteryManager⢠is a single-cell Lithium-
Ion (Li-Ion)/Li-Polymer battery charger IC, designed to
operate from USB ports, AC adapter inputs, or from a
charger adapter up to an input voltage of 6.5V. For
increased safety, the AAT3783 also includes over-voltage
input protection (OVP) up to 28V.
The AAT3783 precisely regulates battery charge voltage
and current for 4.2V Li-Ion/Polymer battery cells through
an extremely low RDS(ON) switch. When charged from an
adapter or a USB port, the battery charging current can
be set by an external resistor up to 1A. In the case of an
over-voltage condition in excess of 6.5V, a series switch
opens preventing damage to the battery and charging
circuitry. With the addition of an external resistor the
OVP trip point can be programmed to a level other than
the factory set value of 6.5V. In the case of an OVP con-
dition a fault flag is activated.
Battery charge state is continuously monitored for fault
conditions. In the event of an over-current, battery over-
voltage, short-circuit or over-temperature failure, the
device will automatically shut down, thus protecting the
charging device, control system and the battery under
charge. A status monitor output pin is provided to indi-
cate the battery charge status by directly driving an exter-
nal LED. An open-drain power-source detection output
(ADPP) is provided to report the power supply status.
The AAT3783 comes in a thermally enhanced, space-
saving, Pb-free 16-pin 3x4 mm TDFN package and is
specified for operation over the -40°C to +85°C tem-
perature range.
Typical Application
Features
⢠USB or AC Adapter System Power Charger
⢠Programmable from 100mA to 1A Max
⢠4.0V ~ 7.5V Input Voltage Range
⪠Over-Voltage Input Protection up to 28V
⢠High Level of Integration with Internal:
⪠Charging Device
⪠Reverse Blocking Diode
⪠Current Sensing
⢠Digital Thermal Regulation
⢠Charge Current Programming (ISET)
⢠Charge Termination Current Programming (TERM)
⢠Charge Timer (CT)
⢠Battery Temperature Sensing (TS)
⢠TS Pin Open Detection
⢠Automatic Recharge Sequencing
⢠No Trickle Charge Option Available
⢠Full Battery Charge Auto Turn Off / Sleep State /
Charge Termination
⢠Automatic Trickle Charge for Battery Pre-conditioning
⢠Battery Over-Voltage and Over-Current Protection
⢠Emergency Thermal Protection
⢠Power On Reset
⢠16-pin 3x4mm TDFN Package
Applications
⢠Bluetooth⢠Headsets, Headphones, Accessories
⢠Digital Still Cameras
⢠Mobile Phones
⢠MP3 Players
⢠Personal Data Assistants (PDAs)
⢠Other Li-Ion/Polymer Battery Powered Devices
VIN
2.2μF
Enable Charging
Enable OVP
IN
BATS
IN
BAT
FLT AAT3783
OVP
INCHR
TS
STAT
ADPP
ENCHR
CT
TERM
ISET
ENOVP GND
10μF
RSET
BATT+
BATT-
TEMP
Battery
Pack
RTERM
CT
3783.2007.12.1.0
www.analogictech.com
1
|
▷ |