|
AS3658 Datasheet, PDF (1/3 Pages) ams AG – Power and Audio Management Unit for Portable Devices | |||
|
AS3658
Product Brief
AS3658
Power and Audio Management Unit for Portable Devices
Product Brief
1 General Description
The AS3658 is highly integrated power and audio
management unit. It includes all the features from
the AS3654 and adds on top an 16 bit Audio ADC,
a second headphone amplifier, a microphone bias
with amplifier, a RTC with alarm and time function,
an unique ID block and three more LDOs.
2 Key Features
 System Control
â Serial Control Interface
â On/Off Control Module with Boot-ROM /
GPIO
â Reset Generation for system controller
â Programmable Interrupt Controller and
Watchdog
â Low power off mode (9μA; 2.5V LDO on)
â 88 bit unique ID or Boot fuse array
â Reset with long ON-Keypress (5s, SW-
Interuptable)
â Touchscreen Interface (10 bit, interrupt)
 Supply Voltage Generation
â 2 RF Programmable Low Noise LDOs
(250mA)
(1 LDO can be a current controlled switch
for hotplug (200mA +/-40%))
â 1 RF Programmable Low Noise LDO
(400mA)
â 4 Programmable Dig. Low Power
LDOs(200mA)
â 2 General Purpose PWM DC/DC step up
converter with three programmable current
sinks (e.g. for white led); for current mode
feedback is automatically slected
(DCDC_CURR1,2,3)
â 3 General Purpose high efficiency DC/DC
step down converter (DCDC 1 support
DVM)
â 1 Low noise charge pump with 5V output
voltage
â 1 Ultra Low Power 2.5V LDO (always on)
 Current sinks
â 4 programmable(8-bit) from 0.15mA to
38.25mA (+/-5% ) optional useable as
GPIOs
â 3 programmable high voltage (15V) (8-bit)
from 0.15mA to 38.25mA (+/-5% )
â internal PWM generator (extended time
range)
(can control DCDC_CURR1,2,3)
 10-bit 40μs Successive Approximation ADC
â Two external Inputs (ADC_IN1, ADC_IN2)
 Battery Management
â Full featured chemistry independent step
down charger with Gas Gauge and Current
limitation
â High Current (1.0A) Linear Charger with
external pass transistor (no SD charger)
â 0.1 Ω Battery switch for start-up and trickle
charge
â Integrated USB charger up to 880mA (can
be used as wall adapter charger); current
accuracy 440-500mA for USB specification,
in-circuit trimmable (+/-1.2% trimsteps)
â Autonomous Battery Temperature
Supervision (0°C-45°C or 0°C- 50°C) for
10k and 100k NTC
â Charging Timeout (1h-8h in 30min steps)
â Charging in Stanby mode
â Completely Autonomous (no SW)
 Power Management Features
â Wide Battery Supply Range 3.0â¦5.5V
â High Accuracy Reference (±1%)
â Thermal and Current Protection (int.
sensor)
â Standby Mode exit by interrupt
e.g.Onkey/RTC
 Audio
â 94dB Audio DAC, 16-48kHz sampling rate
â Two Digital Audio Inputs (2 x I2S interface)
â 2.9V low Noise LDO for Audio DAC
â Two Headphone Amplifier Output with GND
separation
â Two I2S Inputs and one I2S Output
â I2S master mode with programmable
sample rate (controlled by internal PLL)
â GND Buffer for Headphone Amplifier
â Line/ Headphone outputs with GND
separation
â Audio ADC, 82dB SNR with 16ksps
â Mono Microphone Supply and Amplifier
â 5 Band Adjustable Audio Equalizer (+/-
12dB in 3dB gain steps)
â SPDIF Output
â Audio Mixer and Gain Stages
â PCM Interface
 Real Time Clock (RTC)
â Alarm and Time function
â Repeated Wakeup (every sec. or minute)
â 32kHz output
â Backup Battery Charger and Switchover
 Programmable System clock
â 1.6 MHz to 2.3 MHz with 100 kHz steps
 Package
â BGA124 8x8mm, 0.5mm pitch (can be
assembled without microvia boards)
3 Application
â PDA, PMP, GPS-Navigation System
â 1 Cell Li+ or 3 Cell NiMH powered devices
www.austriamicrosystems.com (ptr)
Revision 1.4 / 20071217
1-3
|
▷ |