PSP240_1 Datasheet, PDF (1/2 Pages) Altech corporation – 240W Single Phase Industrial DIN Rail Power Supply

240W Single Phase Industrial DIN Rail Power Supply
PSP-240 Series
F ea tures :
Univers al A C i nput / F ull range
B uilt in a ctive P F C f unction, P F >0.95
P rotections :S hort circuit/O ver loa d/O ver v olta ge/O ver tempera ture
C ooling by f ree a ir c onvection
C a n be i ns ta lled on D IN r a il T S -35/7.5 o r 1 5
U L 5 08(indus tria l c ontrol e quipment)a pproved
L E D i ndica tor for power o n
100% f ull load burn-in tes t
F ixed s witching frequency a t 100K Hz
3 y ea rs w a rra nty
R
S PE CIFICATION
MODE L
PSP-24024
PSP-24048
DC VOLTAGE
24V
48V
RATED CURRENT
10A
5A
CURRENT RANGE
0 ~ 10A
0 ~ 5A
RATED POWER
240W
240W
OUTPUT
RIPPLE & NOISE (max.) Note.2 80mVp-p
VOLTAGE ADJ . R ANGE
24 ~ 28V
VOLTAGE TOLERANCE Note.3 1.0%
150mVp-p
48 ~ 53V
1.0%
LINE R EGULATION
0.5%
0.5%
LOAD REGULATION
1.0%
1.0%
SETUP, R ISE, HOLD TIME 800ms, 40ms, 20ms/230VAC 8 00ms, 40ms, 20ms/115VAC at full load
VOLTAGE R ANGE
85 ~ 264VAC 1 20 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF>0.95/230VAC P F>0.98/115VAC at full load
INPUT EFFICIENCY (Typ.)
84%
85%
AC CURRENT
INRUSH CURRENT (max.)
LEAKAGE C URRENT
OVER L OAD
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
2.8A/115V AC 1.4A/230V AC
COLD START 27A/115V AC 45A/230V AC
<3.5mA / 240VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
30 ~ 36V
54 ~ 60V
Protection type : Shut down o/p voltage, re-power on to recover
100 5 (TSW1)Detect on heat sink of power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIB R ATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
-10 ~ +70 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL508, UL60950-1, EN60950 Approved
I/P-O/P:3KVAC I /P-FG:1.5KVAC O/P-FG:0.5KVAC
SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
E MC
(Note 4)
EMI CONDUCTION & RADIATION Compliance to EN55011,EN55022 (CISPR22) Class B
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
OTHE R S
NOTE
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,61,8, ,E1NV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, cAriteria
MTB F
105.5Khrs min. MIL-HDBK-217F (25 )
DIME NS ION
125.5*125.2*100mm (W*H*D)
PACK ING
1.2Kg; 20pcs/14.4Kg/1.2CUFT
1. A ll parameters N OT s pecially mentioned a re measured a t 230VAC i nput, r ated load a nd 25 of ambient temperature.
2. R ipple & n oise a re measured a t 20MHz o f bandwidth by using a 1 2" twisted pair-wire terminated with a 0 .1uf & 4 7uf parallel capacitor.
3. T olerance : i ncludes s et up tolerance, line regulation a nd load regulation.
4. T he power s upply is c onsidered a c omponent which will be installed into a f inal equipment. T he final equipment must be re-confirmed that it still meets
E MC d irectives.
35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com