PS75_1 Datasheet, PDF (1/2 Pages) Altech corporation – 75W Single Phase Industrial DIN Rail Power Supply

75W Single Phase Industrial DIN Rail Power Supply
PS-75 Series
F ea tures :
U nivers a l A C i nput/F ull ra nge
P rotections :Short circuit/O ver loa d/O ver v olta ge/O ver tempera ture
C ooling by f ree a ir c onvection
C a n be i ns ta lled on D IN r a il T S -35/7.5 o r 1 5
U L 5 08(indus tria l c ontrol e quipment)a pproved
L E D i ndica tor for power o n
100% f ull load burn-in tes t
F ix switching frequency a t 50K Hz
3 y ea rs w a rra nty
R
S PE CIFICATION
MODE L
PS-7512
PS-7524
PS-7548
DC VOLTAGE
12V
24V
48V
RATED CURRENT
6.3A
3.2A
1.6A
CURRENT RANGE
0 ~ 6.3A
0 ~ 3.2A
0 ~ 1.6A
RATED POWER
76W
76.8W
76.8W
RIPPLE & NOISE (max.) Note.2 100mVp-p
OUTPUT
VOLTAGE ADJ . R ANGE
12 ~ 14V
150mVp-p
24 ~ 28V
240mVp-p
48 ~ 53V
VOLTAGE TOLERANCE Note.3 2.0%
1.0%
1.0%
LINE R EGULATION
0.5%
0.5%
0.5%
LOAD REGULATION
1.0%
1.0%
1.0%
SETUP, R ISE, HOLD TIME 1000ms, 60ms, 50ms/230VAC 1 800ms, 60ms, 10ms/115VAC at full load
VOLTAGE R ANGE
85 ~ 264VAC 1 20 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
EFFICIENCY (Typ.)
76%
80%
81%
INPUT
AC CURRENT
1.6A / 115V AC 0.96A / 230V AC
INRUSH CURRENT (max.) COLD START 20A / 115V AC 40A / 230V AC
LEAKAGE C URRENT
<1mA / 240VAC
OVER L OAD
105 ~ 150% rated output power
Protection type : Constant current li miting, recovers automatically after fault condition is removed
PROTECTION OVER VOLTAGE
15 ~ 16.5V
29 ~ 34V
58 ~ 65V
Protection type : Hiccup mode, recovers automatically after fault condition is removed
OVER TEMPERATURE
85 5 (TSW1) Detect on heat sink of power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP.
-10 ~ +60 (Refer to output load derating curve)
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY ^{-20 ~ +85 , 10 ~ 95% RH}
TEMP. COEFFICIENT
0.03%/ (0 ~ 50
VIB R ATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL508, EN60950 Approved
SAFETY &
E MC
(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMI CONDUCTION & RADIATION
HARMONIC CURRENT
I/P-O/P:3KVAC I /P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
Compliance to EN55011,EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,61,8, ,E1NV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, cAriteria
MTB F
123.1K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
55.5*125.2*100mm (W*H*D)
PACK ING
0.6Kg; 20pcs/13Kg/1.1CUFT
NOTE
1. A ll parameters N OT s pecially mentioned a re measured a t 230VAC i nput, r ated load a nd 25 of ambient temperature.
2. R ipple & n oise a re measured a t 20MHz o f bandwidth by using a 1 2" twisted pair-wire terminated with a 0 .1uf & 4 7uf parallel capacitor.
3. T olerance : i ncludes s et up tolerance, line regulation a nd load regulation.
4. T he power s upply is c onsidered a c omponent which will be installed into a f inal equipment. T he final equipment must be re-confirmed that it still meets
E MC d irectives.
35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com