PS120_1 Datasheet, PDF (1/2 Pages) Altech corporation – 120W Single Output Industrial DIN Rail Power Supply

120W Single Output Industrial DIN Rail Power Supply
PS-120 Series
F ea tures :
AC i nput ra nge s electa ble b y s witch
P rotections :S hort circuit/O ver loa d/O ver v olta ge/O ver tempera ture
C ooling by f ree a ir c onvection
C a n be i ns ta lled on D IN r a il T S -35/7.5 o r 1 5
U L 5 08(indus tria l c ontrol e quipment)a pproved
L E D i ndica tor for power o n
100% f ull loa d burn-in tes t
F ixed s witching frequency a t 55K Hz
3 y ea rs w a rra nty
R
S PE CIFICATION
MODE L
PS-12012
PS-12024
PS-12048
DC VOLTAGE
12V
24V
48V
RATED CURRENT
10A
5A
2.5A
CURRENT RANGE
0 ~ 10A
0 ~ 5A
0 ~ 2.5A
RATED POWER
120W
120W
120W
OUTPUT
RIPPLE & NOISE (max.) Note.2 80mVp-p
VOLTAGE ADJ . R ANGE
12 ~ 14V
VOLTAGE TOLERANCE Note.3 2.0%
80mVp-p
24 ~ 28V
1.0%
100mVp-p
48 ~ 53V
1.0%
LINE R EGULATION
0.5%
0.5%
0.5%
LOAD REGULATION
1.0%
1.0%
1.0%
SETUP, R ISE, HOLD TIME 500ms, 70ms, 30ms/230VAC 500ms, 70ms, 30ms/115VAC at full load
VOLTAGE R ANGE
88 ~ 132VAC/176 ~ 264VAC by switch 248 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
INPUT
EFFICIENCY (Typ.)
AC CURRENT
INRUSH CURRENT (max.)
LEAKAGE C URRENT
OVER L OAD
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIB R ATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
80%
84%
85%
2.6A / 115V AC 1.6A / 230V AC
Cold Start 20A /115V AC 40A / 280V AC
<3.5mA / 240VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
15 ~ 16.5V
29 ~ 33V
58 ~ 65V
Protection type : Shut down o/p voltage, re-power on to recover
85 5 (TSW1)
90 5 (TSW1)
90 5 (TSW1)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
-10 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL508,UL60950-1, EN60950 Approved
I/P-O/P:3KVAC I /P-FG:1.5KVAC O/P-FG:0.5KVAC
SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
E MC
(Note 4)
EMI CONDUCTION & RADIATION Compliance to EN55011,EN55022 (CISPR22) Class B
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
OTHE R S
EMS IMMUNITY
MTB F
DIME NS ION
PACK ING
Compliance to EN61000-4-2,3,4,5,61,8, ,E1NV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, cAriteria
136.8Khrs min. MIL-HDBK-217F (25 )
65.5*125.2*100mm (W*H*D)
0.79Kg; 20pcs/16.5Kg/1.1CUFT
NOTE
1. A ll parameters N OT s pecially mentioned a re measured a t 230VAC i nput, r ated load a nd 25 of ambient temperature.
2. R ipple & n oise a re measured a t 20MHz o f bandwidth by using a 1 2" twisted pair-wire terminated with a 0 .1uf & 4 7uf parallel capacitor.
3. T olerance : i ncludes s et up tolerance, line regulation a nd load regulation.
4. T he power s upply is c onsidered a c omponent which will be installed into a f inal equipment. T he final equipment must be re-confirmed that it still meets
E MC d irectives.
35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com