5816 Datasheet, PDF (4/4 Pages) Allegro MicroSystems – 4-TO-16 LINE LATCHED DECODER/DRIVERS

5816
4-TO-16 LINE LATCHED DECODER/DRIVERS
CLEAR
F
STROBE
OUTPUT
ENABLE
INN
OUTN
A
CB
G
CB
D
E
A
CB
G
E
p/o Dwg. No. A-10,895A
TIMING CONDITIONS
(Logic Levels are V_DD and Ground)
A. Minimum Data Active Time Before Strobe Enabled
(Data Set-Up Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ns
B. Minimum Data Active Time After Strobe Disabled
(Data Hold Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ns
C. Minimum Strobe Pulse Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ns
D. Typical Time Between Strobe Activation and Output On to
Off Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 ns
E. Typical Time Between Strobe Activation and Output Off to
On Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 ns
G. Minimum Data Pulse Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 ns
TRUTH TABLE
Information present at the inputs is
transferred to the latches when the STROBE
is high. The latches will continue to accept
new data as long as the STROBE is held
high. With the STROBE in the low state, no
information can be loaded into the latches.
Depending on the four address inputs, the
4-to-16 line decoder enables one of the
16 output sink drivers. When the OUTPUT
ENABLE is high, all of the outputs are
disabled (OFF) without affecting the informa-
tion stored in the latches. When the OUT-
PUT ENABLE is low, the outputs are con-
trolled by the information in the latches.
When the CHIP ENABLE is low, all of the
outputs are disabled (OFF). With two de-
coder/drivers and an inverter, the CHIP
ENABLE function can be used for 5-to-32 line
decoding applications.
CHIP
IN_D
IN_C
STROBE ENABLE
(MSB)
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
X
X
X
0
X
X
X
X
X
X
IN_B
IN_A
OUTPUT
OUTPUTS
(LSB) ENABLE (OFF unless otherwise specified)
0
0
0
0
1
0
1
0
0
1
1
0
0
0
0
0
1
0
1
0
0
1
1
0
0
0
0
0
1
0
1
0
0
1
1
0
0
0
0
0
1
0
1
0
0
1
1
0
X
X
0
X
X
X
OUT₀ON
OUT₁ ON
OUT₂ ON
OUT₃ ON
OUT₄ ON
OUT₅ ON
OUT₆ ON
OUT₇ ON
OUT₈ ON
OUT₉ ON
OUT₁₀ ON
OUT₁₁ ON
OUT₁₂ ON
OUT₁₃ ON
OUT₁₄ ON
OUT₁₅ ON
Q_O
All OFF
X
X
1
All OFF
Q_O = The output condition prior to the high-to-low transition of the STROBE input.
X = Irrelevant
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]