ALD1502SAL Datasheet, PDF (1/10 Pages) Advanced Linear Devices – SINGLE/DUAL PRECISION HIGH SPEED MICROPOWER TIMER

ADVANCED
LINEAR
DEVICES, INC.
ALD1502/ALD2502
SINGLE/DUAL PRECISION HIGH SPEED MICROPOWER TIMER
GENERAL DESCRIPTION
The ALD1502/ALD2502 timers are high performance single/dual mono-
lithic timing circuits built with advanced silicon gate CMOS technology.
They offer the benefits of high input impedance, thereby allowing
smaller timing capacitors and a longer timing cycle; high speed, with
typical cycle time of 400ns; low power dissipation for battery operated
environment; reduced supply current spikes, allowing smaller and
lower cost decoupling capacitors.
Each timer is capable of producing accurate time delays and oscilla-
tions in both monostable and astable operation, and operates in the
one-shot (monostable) mode or 50% duty cycle free running oscillation
mode with a single resistor and one capacitor. The inputs and outputs
are fully compatible with CMOS, NMOS or TTL logic.
There are three matched internal resistors (approximately 200KΩ
each) that set the threshold and trigger levels at two-thirds and one-third
respectively of V^+. These levels can be adjusted by using the control
terminal. When the trigger input is below the trigger level, the output is
in the high state and sourcing 2mA. When the threshold input is above
the threshold level at the same time the trigger input is above the trigger
level, the internal flip-flop is reset, the output goes to the low state and
sinks up to 10mA. The reset input overrides all other inputs and when
it is active (reset voltage less than 1V), the output is in the low state.
FEATURES
• High speed operation -- 2.5MHz typical oscillation at 5V
• High discharge sinking current of 80mA at 5V
• Guaranteed low operating supply voltage of 2V to 12V
• Functional equivalent to and same pin-out as NE555/NE556
with greatly expanded high and low frequency ranges
• High speed, low power, monolithic CMOS technology
• Low supply current: 50µA typical for ALD1502
and100µA typical for ALD2502
• Extremely low trigger, threshold and reset currents: 10pA typical
• Operates in both monostable and astable modes
• Fixed 50% duty cycle or adjustable duty cycle
• CMOS, NMOS and TTL compatible input/output
• Low supply current spikes
ORDERING INFORMATION (“L” suffix denotes lead-free (RoHS))
0°C to +70°C
Operating Temperature Range *
0°C to +70°C
-55°C to +125°C
8-Pin Small Outline
Package (SOIC)
ALD1502SAL
8-Pin Plastic
DIP Package
ALD1502PAL
8-Pin CERDIP
Package
ALD1502DA
14-Pin Small Outline
14-Pin Plastic
14-Pin CERDIP
Package (SOIC)
DIP Package
Package
ALD2502SBL
ALD2502PBL
ALD2502DB
* Contact factory for leaded (non-RoHS) or high temperature versions.
APPLICATIONS
• High speed one-shot (monostable)
pulse generation
• Precision timing
• Sequential timing
• Long delay timer
• Pulse width and pulse position
modulation
• Missing pulse detector
• Frequency divider
• Synchronized timer
PIN CONFIGURATION
ALD1502
GND 1
TRIG 2
OUT 3
RST 4
8 V+
7 DISC
6 THRES
5 CONT
SAL, PAL, DA PACKAGES
DSC1 1
THRES1 2
CONT1 3
RST1 4
OUT1 5
TRIG1 6
GND 7
ALD2502
14 V+
13 DSC2
12 THRES2
11 CONT2
10 RST2
9 OUT2
8 TRIG2
SBL, PBL, DB PACKAGES
BLOCK DIAGRAM (EACH TIMER)
V+
(8)
THRESHOLD
(6)
R
CONTROL
(5)
R
TRIGGER
(2)
R
RESET
(4)
R
S
OUTPUT
(3)
DISCHARGE
(7)
GND
(1)
Rev 2.0 ©2010 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, CA 94089-1706 Tel: [phone] Fax: [phone]
www.aldinc.com