AMLB-Z_16 Datasheet, PDF (2/7 Pages) AIMTEC – Up to 900mA | Step Up LED Driver

Output Specifications (continued)
Parameters
Soft Start Time
Under Voltage Lock Out (Module on / off)
Temperature Coefficient
Ripple & Noise
Conditions
(100 to 700mA)
(900mA)
20MHz Bandwidth
Series AMLB-Z
Up to 900mA | Step Up LED Driver
Typical
Maximum
50
7.6 / 6.8
15.6 / 14.6
±0.03
See model table
Units
ms
VDC
%/^oC
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Operating Frequency
Depending on the model
360-380
KHz
AMLB-3615Z
-40 to +85
AMLB-3625Z; AMLB-3630Z
-40 to +80 (Vin 9-18V) / -40 to +85 (Vin 18-36V)
Operating Temperature
AMLB-3635Z
AMLB-3650Z
-40 to +75 (Vin 9-18V) / -40 to +85 (Vin 18-36V)
-40 to +70 (Vin 9-18V) / -40 to +80 (Vin 18-36V)
o_C
AMLB-3660Z; AMLB-3670Z
-40 to +70 (Vin 9-18V) / -40 to +75 (Vin 18-36V)
AMLB-3690Z
-40 to +65
Storage Temperature
-55 to +125
o_C
Maximum Case Temperature
100
o_C
Thermal Impedance
Depending on the model
+13.7 to +17
o_C/W
Cooling
Free air convection
Humidity
95
% RH
Case material
Non-Conductive Black Plastic (UL94-V0 rated)
Weight
38
g
Dimensions (L x W x H)
2.03 x 1.03 x 0.62 inches
51.50 x 26.10 x 15.80 mm
MTBF
> 1 290 000 hrs (MIL-HDBK-217 F at +25 ^oC/Vin=9V,Vout=38V)
Maximum Soldering Temperature 1.5mm from case for 10sec.
260
o_C
NOTES:
1. To prevent burning out the driver, the output voltage must be 5.0VDC higher than the input voltage
2. Do NOT exceed the maximum power ratings on each model
3. With output ripple being rather low, it is recommended not to increase the additional output capacitor so s not to increase the delay while starting up
under cool start conditions
4. This series offers protection in case the output is shorted. After the short occurs, the input current will be cut off and recovers when the short is removed
5. The reference value of under voltage protection (7.6V) means that under the condition of cool start and full discharge of output, the protection starts when
input voltage is lower than 7.6V
6. Note: PWM dimming means PWM signals are converted into mimic analog voltage by internal circuits and then do the dimming. The advantage of this
approach is to reduce the EMI
Safety Specifications
Parameters
Agency approvals
Standards
CE, EN 55015, EN 61547, NOTE: Designed to meet EN 55022 Class B, IEC/EN 60950-1 , UL8750,
IEC/EN 61347-2-13
Electrostatic Discharge Immunity
IEC 61000-4-2
RF, Electromagnetic Field Immunity
IEC 61000-4-3
Electrical Fast Transient/Burst Immunity
IEC 61000-4-4
Surge Immunity
IEC 61000-4-5
RF, Conducted Disturbance Immunity
IEC 61000-4-6
Power frequency Magnetic Field Immunity
IEC 61000-4-8
Voltage dips, Short Interruptions Immunity
IEC 61000-4-11
Pin Out Specifications
Pin
Single
1
+Vi
2
DIM
3
ON/OFF
4
-Vi
5
+LED
6
-LED
Description
+ DC Supply
PWM/Analog Dimming Control
Remote ON/OFF
-DC Supply
LED Anode connection
LED Cathode connection
www.aimtec.com
F 051e R12.F
Tel: [phone]
2 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only